To study the energy evolution and failure characteristics of saturated sandstone under unloading conditions, rock unloading tests under different stress paths were conducted. The energy evolution mechanism of the unloading failure of saturated sandstone was systematically explored from the perspectives of the stress path, the initial confining pressure, and the energy conversion rate. The results show that (1) before the peak stress, the elastic energy increases with an increase in deviatoric stress, while the dissipated energy slowly increases first. After the peak stress, the elastic energy decreases with the decrease of deviatoric stress, and the dissipated energy suddenly increases. The energy release intensity during rock failure is positively correlated with the axial stress. (2) When the initial confining pressure is below a certain threshold, the stress path is the main factor influencing the total energy difference. When the axial stress remains constant and the confining pressure is unloading, the total energy is more sensitive to changes in the confining pressure. When the axial stress remains constant, the compressive deformation ability of the rock cannot be significantly improved by the increase in the initial confining pressure. The initial confining pressure is positively correlated with the rock's energy storage limit. (3) The initial confining pressure increases the energy conversion rate of the rock; the initial confining pressure is positively correlated with the energy conversion rate; and the energy conversion rate has a high confining pressure effect. The increase in the axial stress has a much greater impact on the elastic energy than the confining pressure. (4) When the deviatoric stress is small, the confining pressure mainly plays a protective role. Compared with the case of triaxial compression paths, the rock damage is more severe under unloading paths, and compared with the case of constant axial stress, the rock damage is more severe under increasing axial stress.

Implementing compressed air energy storage (CAES) in lined caverns provides a promising technical solution for large-scale energy storage, and the reasonable selection of sealing materials is essential for its success. Flexible membrane materials including sprayable polymers, rubber sheets, and airbags have recently been considered economical and practical sealing options. However, research on flexible membrane sealed CAES caverns remains limited, particularly regarding their mechanical response and parameter sensitivities. To address this gap, an elastic multilayer thick-walled cylinder model verified by physical model tests is proposed. Analytical solutions for the stress and displacement fields of the surrounding rock and concrete lining are derived, and a calculation scheme is designed to evaluate the influence and sensitivity of key parameters. Results indicate that under high internal pressure, both the lining and surrounding rock undergo radial compression without yielding, whereas the lining experiences adverse tensile stresses in the hoop direction. The maximum hoop tensile stress reached the order of 1~3 MPa under typical CAES operating pressures, and tensile-compressive stress transformation may occur in the lining under certain parameter combinations. Sensitivity analysis further shows that internal pressure, in situ stress, surrounding rock elastic modulus, and cavern radius are the dominant factors influencing the mechanical behavior of the system, while geometric and lining parameters have secondary but non-negligible effects. The findings provide theoretical support for the stability analysis and material design of flexible membrane sealed CAES caverns and offer useful guidance for determining allowable operating pressures and selecting lining configurations.

The underground energy geostructure represented by the energy pile is one of the key paths for the cooperative development of underground space and geothermal energy. Because of its advantages of low cost, high efficiency and no extra occupation of underground space, it has become a feasible alternative to the borehole heat exchanger. The change in the temperature field of the energy pile and its surrounding ground not only affects the geological environment but also influences the thermomechanical performance and the durability of the structure. However, the temporal and spatial unsteady-state temperature distribution of piles and surrounding rock under typical intermittent and unbalanced thermal load conditions is still unclear. In this paper, a finite element model was applied to analyze the unsteady-state temperature distribution, and the thermomechanical behavior of the energy pile group was developed and verified. The temperature field distribution of pile and surrounding rock under typical intermittent working and unbalanced thermal load conditions were determined. Moreover, the thermomechanical behavior characteristics of the energy pile group were investigated. Finally, the influences of pile layout on the thermomechanical behavior of the energy pile group were identified by designing six different scenarios. The results indicate that under typical intermittent operation conditions, the temperature of the energy pile and surrounding ground near the heat exchange pipe varies periodically. For areas with unbalanced cooling and heating loads, long-term operation of energy piles leads to thermal accumulation, and the maximum temperature of energy piles occurs in the first daily cycle. In summer/winter working conditions, the increase/decrease in pile temperature induces axial compression/tensile stress. When the pile group is partially used as the energy pile, the non-energy pile acts as the “anchor pile”, and it generates the added tensile stress.

Due to the difficulty of creating directional fractures efficiently and accurately with existing non-explosive rock-breaking methods, a directional fracturing technique utilizing a coal-based solid waste expansive agent, termed the instantaneous expansion with a single fracture (IESF), has been developed. IESF can generate high-pressure gases within 0.05–0.5 s and utilize gas pressure to achieve directional rock fragmentation. The rock-breaking mechanisms under double-borehole conditions of conventional blasting (CB), shaped charge blasting (SCB), and IESF were studied by theoretical analysis, numerical simulation, and in situ test. The gas pressure distribution within directional fractures of IESF was determined, and the crack propagation criterion between double-borehole was established. Numerical simulation results indicated that the stress distribution in CB was random. SCB exhibited tensile stress of −10.89 MPa in the inter-borehole region and −8.33 MPa on the outer-borehole region, while IESF generated −14.47 MPa and −12.62 MPa in the corresponding regions, demonstrating that stresses generated between adjacent boreholes can be superimposed in the inter-hole region. In CB, strain was concentrated along main fractures. SCB exhibited strains of 7 mm and 8 mm in the shaped charge direction, while non-shaped charge directions showed a strain of 1.5 mm. For IESF, strain in the shaped charge direction measured 6 mm, compared to 1 mm in non-shaped charge directions, resulting in superior directional fracture control. In situ test results from Donglin Coal Mine demonstrated that IESF can form superior directional rock-breaking efficacy compared to both CB and SCB, with the average crack rates of 95.5% by IESF higher than 85.0% by SCB. This technique provides a non-explosive method that realizes precise control of the direction of cracks while avoiding the high-risk and high-disturbance problems of explosives blasting.