Aurpon Shams

Mr. Aurpon Shams

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 May 2024 in Polymers
Verified
Journal Article
Open access
PDF file
ASAurpon Shams
Aurpon Shams
EPEasir Arafat Papon
Easir Arafat Papon
Pravin S. ShindePravin S. Shinde
Pravin S. Shinde
Jason BaraJason Bara
Jason Bara
AHAnwarul Haque
Anwarul Haque
The frontal polymerization (FP) of carbon/epoxy (C/Ep) composites is investigated, considering FP as a viable route for the additive manufacturing (AM) of thermoset composites. Neat epoxy (Ep) resin-, short carbon fiber (SCF)-, and continuous carbon fiber (CCF)-reinforced composites are considered in this study. The evolution of the exothermic reaction temperature, polymerization frontal velocity, degree of cure, microstructures, effects of fiber concentration, fracture surface, and thermal and mechanical properties are investigated. The results show that exothermic reaction temperatures range between 110 °C and 153 °C, while the initial excitation temperatures range from 150 °C to 270 °C. It is observed that a higher fiber content increases cure time and decreases average frontal velocity, particularly in low SCF concentrations. This occurs because resin content, which predominantly drives the exothermic reaction, decreases with increased fiber content. The FP velocities of neat Ep resin- and SCF-reinforced composites are seen to be 0.58 and 0.50 mm/s, respectively. The maximum FP velocity (0.64 mm/s) is observed in CCF/Ep composites. The degree of cure (αc) is observed to be in the range of 70% to 85% in FP-processed composites. Such a range of αc is significantly low in comparison to traditional composites processed through a long cure cycle. The glass transition temperature (Tg) of neat epoxy resin is seen to be approximately 154 °C, and it reduces slightly to a lower value (149 °C) for SCF-reinforced composites. The microstructures show significantly high void contents (12%) and large internal cracks. These internal cracks are initiated due to high thermal residual stress developed during curing for non-uniform temperature distribution. The tensile properties of FP-cured samples are seen to be inferior in comparison to autoclave-processed neat epoxy. This occurs mostly due to the presence of large void contents, internal cracks, and a poor degree of cure. Finally, a highly efficient and controlled FP method is desirable to achieve a defect-free microstructure with improved mechanical and thermal properties.

Verified
Journal Article
Open access
PDF file
ASAurpon Shams
Aurpon Shams
EPEasir Arafat Papon
Easir Arafat Papon
AHAnwarul Haque
Anwarul Haque
The cure kinetics in frontal polymerization (FP) of short carbon-fiber-reinforced composites are investigated numerically, focusing on the influence of fiber aspect ratio, volume fraction, and orientation. A classical heat conduction equation is used in FP, where the enthalpic reaction generates heat. The heat generation term is expressed in terms of the rate of degree of cure (dα/dt) in thermoset resin. A rate equation of the degree of cure for epoxy is established in terms of a pre-exponential factor, activation energy, Avogadro’s gas constant, and temperature. The cure kinetics parameters for epoxy resin used in this study are determined using the Ozawa method. The numerical model was validated with experimental data. The results reveal that the aspect ratio of fibers has a minimal effect on the polymerization time. The volume percentage of fibers significantly influences the curing time and temperature distribution, with higher fiber volume fractions leading to faster curing due to enhanced heat transfer. Additionally, fiber orientation plays a critical role in cure kinetics, with specific angles facilitating more effective heat transfer, thereby influencing the curing rate and frontal velocity. The results offer valuable insights into optimizing the design and manufacturing processes for high-performance epoxy-based composites through FP, where precise control over curing is critical.