This paper presents the state-of-the-art of additive manufacturing of composites for processing functional, load-bearing components. A general overview of different additive manufacturing methods is provided, and specific attention is focused on fused filament fabrication-based composites processing. Different process modeling strategies are summarized, and key aspects of these models are discussed. Significant results such as thermal and fluid flow characteristics, effects of nozzle geometry on melt flow, fiber orientation, bead spreading, and solidification, the formation of residual stresses, and deformation behavior are discussed from computational modeling perspective. The scientific advancement, model limitations, and future modeling needs are prescribed reviewing the current works. A general overview of material development in nano-micro-macro-scale reinforcement is also presented. Different length-scales of reinforcement has its own challenges and promises. The continuous fiber reinforcement has a great potential for being the next-generation composites manufacturing technology. However, the challenges in reducing the void content, better bonding between the fiber–matrix, and layer-layer adhesion, and process uncertainty are some of the key areas yet to advance. Based on the current limitations on computational modeling, materials development, and process modeling studies, future research needs and recommendations are provided.
The frontal polymerization (FP) of carbon/epoxy (C/Ep) composites is investigated, considering FP as a viable route for the additive manufacturing (AM) of thermoset composites. Neat epoxy (Ep) resin-, short carbon fiber (SCF)-, and continuous carbon fiber (CCF)-reinforced composites are considered in this study. The evolution of the exothermic reaction temperature, polymerization frontal velocity, degree of cure, microstructures, effects of fiber concentration, fracture surface, and thermal and mechanical properties are investigated. The results show that exothermic reaction temperatures range between 110 °C and 153 °C, while the initial excitation temperatures range from 150 °C to 270 °C. It is observed that a higher fiber content increases cure time and decreases average frontal velocity, particularly in low SCF concentrations. This occurs because resin content, which predominantly drives the exothermic reaction, decreases with increased fiber content. The FP velocities of neat Ep resin- and SCF-reinforced composites are seen to be 0.58 and 0.50 mm/s, respectively. The maximum FP velocity (0.64 mm/s) is observed in CCF/Ep composites. The degree of cure (αc) is observed to be in the range of 70% to 85% in FP-processed composites. Such a range of αc is significantly low in comparison to traditional composites processed through a long cure cycle. The glass transition temperature (Tg) of neat epoxy resin is seen to be approximately 154 °C, and it reduces slightly to a lower value (149 °C) for SCF-reinforced composites. The microstructures show significantly high void contents (12%) and large internal cracks. These internal cracks are initiated due to high thermal residual stress developed during curing for non-uniform temperature distribution. The tensile properties of FP-cured samples are seen to be inferior in comparison to autoclave-processed neat epoxy. This occurs mostly due to the presence of large void contents, internal cracks, and a poor degree of cure. Finally, a highly efficient and controlled FP method is desirable to achieve a defect-free microstructure with improved mechanical and thermal properties.
13 February 2025 in Composites Part B: Engineering
The cure kinetics in frontal polymerization (FP) of short carbon-fiber-reinforced composites are investigated numerically, focusing on the influence of fiber aspect ratio, volume fraction, and orientation. A classical heat conduction equation is used in FP, where the enthalpic reaction generates heat. The heat generation term is expressed in terms of the rate of degree of cure () in thermoset resin. A rate equation of the degree of cure for epoxy is established in terms of a pre-exponential factor, activation energy, Avogadro’s gas constant, and temperature. The cure kinetics parameters for epoxy resin used in this study are determined using the Ozawa method. The numerical model was validated with experimental data. The results reveal that the aspect ratio of fibers has a minimal effect on the polymerization time. The volume percentage of fibers significantly influences the curing time and temperature distribution, with higher fiber volume fractions leading to faster curing due to enhanced heat transfer. Additionally, fiber orientation plays a critical role in cure kinetics, with specific angles facilitating more effective heat transfer, thereby influencing the curing rate and frontal velocity. The results offer valuable insights into optimizing the design and manufacturing processes for high-performance epoxy-based composites through FP, where precise control over curing is critical.
14 April 2026 in Composites Part A: Applied Science and Manufacturing
Halo-gravity traction (HGT) is widely used as a preoperative treatment for severe pediatric spinal deformities by gradually applying traction forces through a cranial fixation system. Although the clinical effectiveness of HGT has been extensively documented, uncertainty associated with the structural response and operational behavior of mobile HGT systems has received comparatively little attention. This study presents a preliminary coupled clinical–structural uncertainty quantification framework for engineering evaluation of a mobile halo-gravity traction wheelchair. Reduced-order structural and clinical surrogate models are combined with Latin Hypercube Sampling, bounded beta-distributed input variables, third-order Polynomial Chaos Expansion, and Sobol sensitivity analysis. Sixteen uncertain patient, operational, geometric, fabrication, and halo-interface parameters are propagated through models of combined beam–column loading, elastic buckling, welded-joint loading, scenario-based wheelchair tipping stability, halo-pin load concentration, traction delivery, and representative clinical response. Thirty-two alternative beta-distribution shape cases are examined to assess sensitivity to the assumed marginal distribution shapes. Within the investigated bounds and reduced-order modeling assumptions, the computational screening model did not predict loss of the prescribed structural margins. The results identify the parameters governing the different response modes and demonstrate how uncertainty in mobility-related acceleration, support geometry, traction loading, fabrication efficiency, and halo-pin load transfer can be evaluated within a unified framework. Because the model has not yet been validated through dedicated prototype testing or higher-fidelity full-system simulation, the results should be interpreted as uncertainty-informed engineering screening rather than as experimental verification or clinical certification of device safety.