Over the past few years, interest in high-entropic alloys (HEAs) has been growing. A large body of research has been undertaken to study aspects such as the microstructure features of HEAs of various compositions, the effect of the content of certain elements on the mechanical properties of HEAs, and, of course, special properties such as heat resistance, corrosion resistance, resistance to irradiation with high-energy particles, magnetic properties, etc. However, few works have presented results accumulated over several years, which can complicate the choice of directions for further research. This review article presents the results of studies of the mechanisms of high-temperature oxidation of HEAs of systems: Al-Co-Cr-Fe-Ni, Mn-Co-Cr-Fe-Ni, refractory HEAs. An analysis made it possible to systematize the features of high-temperature oxidation of HEAs and propose new directions for the development of heat-resistant HEAs. The presented information may be useful for assessing the possibility of the practical application of HEAs in the aerospace industry, in nuclear and chemical engineering, and in new areas of energy.

The electrochemical behavior of as-cast Al_xCoCrFeNiM (M = Ti, V, Si, Mn, Cu) high entropy alloys (HEAs) in 1 M NaCl and 0.5 M H₂SO₄ solutions is studied. Polarization measurements were carried out in a standard three-electrode electrochemical cell with a platinum auxiliary electrode using a P-30J potentiostat device. The potentials were measured relative to a saturated silver chloride reference electrode EVL-1M3 at room temperature (25 °C) with a sweep rate of 5 mV/s. It is shown that despite a wide passivation region, Al_0.5CoCrFeNi_1.6Ti_0.7 HEA undergoes significant corrosion in both sodium chloride and sulfuric acid solutions and exhibits low corrosion potential and current density. Energy-dispersive X-ray spectroscopy (EDS) analysis revealed that Ti-containing eutectic areas are the most susceptible regions to corrosion. Intergranular corrosion was found in Al_0.25CoCrFeNiMn and Al_0.25CoCrFeNiCu HEAs. Moreover, Al_0.25CoCrFeNiCu possesses the smallest passivation interval ΔE among all the investigated HEAs. For samples with Ti, Mn, and Cu, a protective film layer is not formed on the surface of the phases enriched in these elements, or it is brittle and crumbles. For samples with Si and V, a passivating film is formed. Thus, Al_0.45CoCrFeNiSi_0.45 and Al_0.25CoCrFeNiV HEAs exhibited the highest resistance in 1 M NaCl and 0.5 M H₂SO₄ corrosive environments, respectively.

One of the methods of local improvement of the wear resistance of aluminum alloy parts is the deposition of hard tungsten carbide-based coatings on the surfaces subjected to intense external influence. This paper is devoted to the characterization of the WC–10Co–4Cr (wt.%) coating deposited on an Al–4Cu–1Mg (wt.%) alloy by the detonation spray method. In comparison with the common thermal spray techniques like High Velocity Oxygen Fuel (HVOF) or Atmospheric Plasma Spraying (APS), the heat input delivered to the substrate during detonation spray is significantly lower, that is especially important in case of coating deposition on aluminum alloys. The paper presents the results of morphology investigation, microstructure, phase composition, microhardness, and cohesive strength of deposited carbide-based detonation spray coating. Results showed that the coating has a porosity less than 0.5% and the carbide grain refinement down to the submicron size during coating deposition was detected. According to the investigation, the variation of spraying distance from 270 to 230 mm does not influence on the coating microstructure and composition.

Titanium alloy product manufacturing is traditionally considered to be a rather difficult task. Additive manufacturing technologies, which have recently become quite widespread, can ensure the manufacture of titanium alloys products of an arbitrary geometrical shape. During this study, we have developed a methodology for manufacturing titanium alloys products using additive technologies on FL-Clad-R-4 complex of laser melting of metals by combined Selective Laser Melting (SLM) and Direct Metal Deposition (DMD) methods. Ti–6Al–4V and Ti–6Al–4Mo–1V alloys were used for the manufacture of samples. We studied the microstructure of the obtained details and measured the microhardness of the samples. We discovered a gradient of the structure throughout the height of the details walls, which is connected with the peculiarities of thermal cycles of the technology used. This affected the microhardness values: in the upper part of the details, the microhardness is 10–25% higher (about 500 HV) than in the lower part (about 400 HV). Products made according to the developed technique do not have visible defects and pores. The obtained results indicate the competitiveness of the proposed methodology.

The influence of laser power on the microstructural, strength, and tribological characteristics of aluminum bronze coatings applied to steel by laser cladding was studied. It was found that with an increase in laser power, the morphology of the coating surface becomes more uniform without extreme height differences. This study revealed that the coating microstructure corresponds to that of a composite material and consists of a bronze matrix and iron dendrites of different sizes (depending on the laser power). Such a microstructure affects the microhardness indices, which have a scatter of values over the coating thickness. There is a diffusion zone at the steel–bronze interface, which promotes adhesion of the matrix and coating materials. According to the results of tribological tests, the dry friction coefficient for the studied samples is in the range of 0.389–0.574.