The objective of this study is to investigate the formation of the structure and stress–strain state in the joints of AISI 304 stainless steel with a thickness of 2 mm and produced by welding with laser and plasma energy sources. It is established that the microhardness and parameters of the grain and subgrain structures of the welded joint material differ with respect to the dimensions of crystallites, grains, and subgrains according to the welding process. It is shown that, in terms of structure formation, including substructural features, the most favorable structures of 2 mm AISI 304 welded joints are formed by laser–plasma welding. It is predicted that the residual stressed state is less localized with the application of laser–plasma welding than laser welding, and it is characterized by a lower level of residual stresses compared to plasma welding. In all the cases, the maximal stress values are concentrated in the HAZ, and the value obtained using laser–plasma welding is in an intermediate position (431.7 MPa) between those of the laser (443 MPa) and plasma (413.7 MPa) processes. With laser–plasma and laser welding, displacements (deformations) are minimal and close to 0.2 mm. The method of electron speckle interferometry was used, and the results reveal that the error between the calculated and experimental values of equivalent stresses is no more than 6%, which is acceptable. The results of mechanical testing show that, under uniaxial tension, the strength of the welded joints made of AISI 304 steel using laser–plasma and laser welding is the highest and equal to 97% of that of the base metal.

Difficult, extreme operating conditions of parabolic antennas under precipitation and sub-zero temperatures require the creation of effective heating systems. The purpose of the research is to develop a multilayer coating containing two metal-ceramic layers, epoxy composite layers, carbon fabric, and an outer layer of basalt fabric, which allows for effective heating of the antenna, and to study the properties of this coating. The multilayer coating was formed on an aluminum base that was subjected to abrasive jet processing. The first and second metal-ceramic layers, Al₂O₃ + 5% Al, which were applied by high-speed multi-chamber cumulative detonation spraying (CDS), respectively, provide maximum adhesion strength to the aluminum base and high adhesion strength to the third layer of the epoxy composite containing Al₂O₃. On this not-yet-polymerized layer of epoxy composite containing Al₂O₃, a layer of carbon fabric (impregnated with epoxy resin) was formed, which serves as a resistive heating element. On top of this carbon fabric, a layer of epoxy composite containing Cr₂O₃ and SiO₂ was applied. Next, basalt fabric was applied to this still-not-yet-polymerized layer. Then, the resulting layered coating was compacted and dried. To study this multilayer coating, X-ray analysis, light and raster scanning microscopy, and transmission electron microscopy were used. The thickness of the coating layers and microhardness were measured on transverse microsections. The adhesion strength of the metal-ceramic coating layers to the aluminum base was determined by both bending testing and peeling using the adhesive method. It was established that CDS provides the formation of metal-ceramic layers with a maximum fraction of lamellae and a microhardness of 7900–10,520 MPa. In these metal-ceramic layers, a dispersed subgrain structure, a uniform distribution of nanoparticles, and a gradient-free level of dislocation density are observed. Such a structure prevents the formation of local concentrators of internal stresses, thereby increasing the level of dispersion and substructural strengthening of the metal-ceramic layers’ material. The formation of materials with a nanostructure increases their strength and crack resistance. The effectiveness of using aluminum, chromium, and silicon oxides as nanofillers in epoxy composite layers was demonstrated. The presence of structures near the surface of these nanofillers, which differ from the properties of the epoxy matrix in the coating, was established. Such zones, specifically the outer surface layers (OSL), significantly affect the properties of the epoxy composite. The results of industrial tests showed the high performance of the multilayer coating during antenna heating.

The Paton Welding Journal, 2026, №02. Scientific-technical and production “The Paton Welding Journal” was founded in 1989 and was published in the UK as a full English translation of “Avtomaticheskaya Svarka” (Automatic Welding) journal, which was published in Russian since 1948. Since 2000 publication of “The Paton Welding Journal” continued in Ukraine. (Short history of “The Paton Welding Journal”) The content of “The Paton Welding Journal” includes original articles by authors from around the world in welding, specialty electrometallurgy, technical diagnostics and NDT, as well as related technologies. Content of the Journal also selectively includes translations into English of articles from the following journals, published in Ukrainian and included in the list of professional publications of Ukraine (category “B”) in technical fields of science: “Avtomatychne Zvaryuvannya” (Automatic Welding), ISSN 3041-2374 (print), ISSN 3041-234X (online); “Suchasna Elektrometalurhiya” (Electrometallurgy Today), ISSN 3041-2382 (print), ISSN 3041-2331 (online); “Tekhnichna Diahnostyka ta Neruinivnyi Kontrol” (Technical Diagnostics & Nondestructive Testing), ISSN 041-2358 (print), ISSN 3041-2366 (online)