Fault diagnosis is currently considered a crucial method to enhance the reliability of permanent magnet synchronous motor (PMSM) drives. In this article, an open-circuit fault (OCF) diagnosis method of a voltage source inverter-fed PMSM with model predictive control is proposed. The developed approach mainly consists of fault detection and localization. Besides, the normalized cost function variation is designed as a fault detection indicator according to the impact of OCFs on current signatures. It can not only monitor drive system conditions, but also discriminate fault categories. Afterward, the polarities of normalized αβ -current average values and phase angles of residual current vectors are utilized to locate the exact faulty switch in each fault type. Consequently, a total of 21 possible combinations of faulty switches can be correctly detected and located. Finally, the effectiveness in fault diagnoses and the robustness against operating point variations are verified by the experimental results.
28 February 2018 in IEEE Transactions on Power Electronics
To solve the reactive power sharing issue of the conventional droop control method, communication is commonly used, especially in networked microgrids. However, there are still many occasions where communication has not been established in advance. In such cases, the wireless reactive power sharing strategy based on the virtual impedance optimization can be applied. By designing and optimizing the controller of virtual impedance, the global reactive power sharing error of the microgrid can be minimized. Thus, the reactive power sharing performance of the droop control method is improved accordingly. However, the original optimization method has not considered the different capacities of distributed generation (DG) units, and it is subject to the number of network nodes. In this paper, an enhanced virtual impedance optimization method is proposed to solve the two issues. First, the reactive power estimation method used in the fitness function is modified to adapt to the system that contains DG units with different capacities. Second, a network simplification step is added before the optimization to deal with the system with more nodes. With these improvements, the application scope of the virtual impedance optimization method is greatly extended. Finally, the effectiveness of the enhanced method is verified through a 38-bus system in MATLAB simulation.
12 February 2019 in IEEE Journal of Emerging and Selected Topics in Power Electronics
This paper mainly focuses on how to provide frequency supports by the doubly fed induction generator (DFIG) during system disturbances. Two coordinated controls that enable system frequency supports by DFIG-based wind turbines (WTs) are proposed in this paper. The first control scheme seeks to render system support via simultaneously utilizing the energy from the installed super-capacitor between the back-to-back converter of DFIG, and WT rotational kinetic energy (KE). The second one stabilizes system frequency by firstly exerting the installed super-capacitor energy and then WT rotational KE via a unique cascading control. Both proposed coordinated control schemes jointly utilize two virtual inertia sources, namely super-capacitor in the DFIG and rotor rotational mass in the WT to fast provide system frequency support. However, the second proposed one stands itself out by reducing its impaired impacts on the overall wind energy production. Two proposed controls on rapidly providing frequency support are effectively verified and compared in detail by different system disturbances in the DIgSILENT/Powerfactory software.
27 January 2022 in IEEE Transactions on Power Electronics
Energy storage system (ESS) has been widely used in photovoltaic system to ensure stable power generation. This article proposes a flying capacitor bidirectional buck–boost converter (FCBBC), aiming at making the ESS work with bidirectional four quadrant in the wide dc+bus voltage variation condition. With the symmetrical modulation strategy, the proposed FCBBC can achieve seamless switching between buck and boost mode to match the voltage changes at energy storage and dc bus side. Meanwhile, considering the ESS application requirements, a fixed frequency model predictive control (MPC) strategy based on binary search algorithm is proposed to achieve the control purpose. The decoupling relationship between flying capacitor (FC) and output voltage is derived so that the proposed MPC strategy can control the voltage of two FCs simultaneously. In addition, the adoption of binary search algorithm effectively reduces the computation load of the proposed MPC strategy. Finally, the effectiveness of the proposed converter and MPC strategy are verified with a downscaled ESS experimental platform.
20 May 2021 in IEEE Transactions on Energy Conversion
This paper proposes an improved SOC balancing strategy for the modular energy storage system (ESS) based on low bandwidth communication (LBC) technology, aiming at solving the drawbacks of the conventional balancing strategy based on droop control. The proposed control scheme can improve the SOC balancing efficiency and remove the current deviation by using the SOC slope-adjusting and current-shifting approaches simultaneously. The average value of SOC can be derived through the LBC line, and the droop coefficient based on SOC can be controlled in the local control layer. Thus, the SOC of each sub-module can converge to the average SOC value in system dynamic process, and the balancing speed under the condition of low SOC difference between sub-modules can be improved. Furthermore, the current regulation performance in steady and transient states can be enhanced by using the proposed method. At last the effectiveness of the proposed strategy is verified by experimental results.