Stope structural parameters are of great significance for the safe production of mines. To efficiently and safely mine steeply dipping ultra-thick ore bodies, the K. Kegel strength design formula and limit analysis method were used to calculate a reasonable range of stope parameters. Considering the actual mining conditions, the mechanical responses under different structural parameters were obtained through numerical simulations based on a central composite experimental design. A regression model for maximum tensile stress, maximum compressive stress, and maximum vertical displacement was established using the second-order response surface method. The regression model was then used as the objective function, and multi-objective optimization was performed using a simulated annealing algorithm to obtain the Pareto optimal solution set. Based on practical engineering needs, a stope span of 15.0 m, a pillar width of 10.0 m, and a roof thickness of 11.9 m were determined as the optimal structural parameters, achieving a balance between safety and economic efficiency.
Coal seam floor water inrush is one of the most significant hazards affecting the safety of coal mine operations. To prevent water inrush incidents, it is critical to investigate the evolution of fault characteristics during the mining of working faces. This study takes the 4104 working face of the Heshan mine in China as the engineering case, and a fluid–solid–damage coupling numerical model of the mining process is established. COMSOL multiphysics software is employed to analyze the evolution of fault characteristics in the coal seam floor under mining-induced disturbances. The results show that under mining disturbances, the stress on the fault plane decreases initially and then increases, with higher stress at the sides and lower stress in the center. These stress variations induce alternating states of sliding and stability on the fault plane, indicating that fault reactivation manifests as a dynamic, non-equilibrium process. As the rock mass gradually deteriorates, the stress field at the fault zone undergoes redistribution, leading to fault reactivation. This process further exacerbates damage to the rock mass, resulting in a continuous increase in the permeability coefficient within the fault zone, thereby elevating the probability of water inrush hazards. Areas with more severe damage typically exhibit higher permeability, forming high-risk zones for water inrush. This study explores the characteristics of fault reactivation and its relationship with the seepage field, providing a theoretical basis for coal mining enterprises to prevent and control fault-induced water inrush.
To ensure the green, safe, and efficient extraction of mineral resources and promote sustainability, the stability of mined-out areas has become a critical factor affecting safe production and ecological restoration in underground metal mines. The instability of underground goafs poses a significant threat to mine safety, especially when irregular excavation patterns interact with high ground stress, exacerbating instability risks. Most existing studies lack a systematic and multidisciplinary integrated framework for comprehensive evaluation and management. This paper proposes a trinity research system of “assessment–optimization–governance”, integrating theoretical analysis, three-dimensional fluid–solid coupling numerical simulation, and a filling sequence optimization method based on genetic algorithms. An analysis of data measured from 243 pillars and 49 goafs indicates that approximately 20–30% of the pillars have a factor of safety (FoS) below 1.0, signaling immediate instability risks; additionally, 58% do not meet the threshold for long-term stability (FoS ≥ 1.5). Statistical and spatial analyses highlight that pillar width-to-height ratio (W/H) and cross-sectional area significantly influence stability; when W/H exceeds 1.5, FoS typically surpasses 2.0. Numerical simulations reveal pore water pressures of 1.4–1.8 MPa in deeper goafs, substantially reducing effective stress and accelerating plastic zone expansion. Stability classification categorizes the 49 goafs into 7 “poor”, 37 “moderate”, and 5 “good” zones. A genetic algorithm-optimized filling sequence prioritizes high-risk area remediation, reducing maximum principal stress by 60.96% and pore pressure by 28.6%. Cemented waste rock filling applied in high-risk areas, complemented by general waste rock filling in moderate-risk areas, significantly enhances overall stability. This integrated method provides a scientific foundation for stability assessment and dynamic remediation planning under complex hydrogeological conditions, offering a risk-informed and scenario-specific application of existing tools that improves engineering applicability.
Mine-induced surface subsidence threatens infrastructure and can trigger cascading geohazards, so accurate and computationally efficient monitoring and forecasting are essential for early warning. We integrate Persistent Scatterer InSAR (PS-InSAR) time series with a Bayesian-optimized CNN–LSTM designed for spatiotemporal prediction. The CNN extracts spatial deformation patterns, the LSTM models temporal dependence, and Bayesian optimization selects the architecture, training hyperparameters, and the most informative exogenous drivers. Groundwater level and backfilling intensity are encoded as multichannel inputs. Endpoint anchoring with affine calibration aligns the historical series and the forward projections. PS-InSAR indicates a maximum subsidence rate of 85.6 mm yr−1, and the estimates are corroborated against nearby leveling benchmarks and FLAC3D simulations. Cross-site comparisons show acceleration followed by deceleration after backfilling and groundwater recovery, which is consistent with geological engineering conditions. A symmetry-aware preprocessing step exploits axial regularities of the deformation field through mirroring augmentation and documents symmetry-breaking hotspots linked to geological heterogeneity. These choices improve generalization to shifted and oscillatory patterns in both the spatial CNN and the temporal LSTM branches. Short-term forecasts from the BO–CNN–LSTM indicate subsequent stabilization with localized rebound, highlighting its practical value for operational planning and risk mitigation. The framework combines automated hyperparameter search with physically consistent objectives, reduces manual tuning, enhances reproducibility and generalizability, and provides a transferable quantitative workflow for forecasting mine-induced deformation in complex goaf systems.