Low thermal conductivity is the main drawback of phase change materials (PCMs) that is yet to be fully addressed. This paper studies several efficient, cost-effective, and easy-to-use experimental techniques to enhance thermal conductivity of an organic phase change material used for low-temperature thermal energy storage applications. In such applications, the challenges associated with low thermal conductivity of such organic PCMs are even more pronounced. In this investigation, polyethylene glycol (PEG-1000) is used as PCM. To improve the thermal conductivity of the selected PCM, three techniques including addition of carbon powder, and application of aluminum and graphite fins, are utilized. For measurement of thermal conductivity, two experimental methods—including flat and cylindrical configurations—are devised and increments in thermal conductivity are calculated. Melting and solidification processes are analyzed to evaluate melting and solidification zones, and temperature ranges for melting and solidification processes respectively. Furthermore, latent heat of melting is computed under constant values of heat load. Ultimately, specific heat of the PCM in solid state is measured by calorimetry method considering water and methanol as calorimeter fluids. Based on the results, the fin stack can enhance the effective thermal conductivity by more than 40 times with aluminum fins and 33 times with carbon fins. For pure PCM sample, Initiation of melting takes place around 37 °C and continues to above 40 °C depending on input heat load; and solidification temperature range was found to be 33.6–34.9 °C. The investigation will provide a twofold pathway, one to enhance thermal conductivity of PCMs, and secondly ‘relatively easy to set-up’ methods to measure properties of pure and enhanced PCMs.
13 October 2021 in Journal of Thermal Science and Engineering Applications
The present paper investigates the potential of loop heat pipe (LHP), with respect to technological merits and application niche, in automotive thermal management. Broadly, LHP design and applicability for hot spot cooling in electronics (local dissipation), and for heat transport over longer distances (remote dissipation) has been proposed and discussed in detail. The basic module in these applications includes loop heat pipe with different shapes and sizing factors. Two types of LHP designs have being tested and results discussed. The miniature version, with 10 mm thick and flat disk evaporator, for cooling electronic control unit (ECU) with 70 W chipset while keeping source temperature below 100 °C limit was evaluated. Two larger versions with cylindrical evaporator, 25 mm diameter and 150 mm length, and heat transfer distances of 250 mm and 1000 mm, respectively, were tested for power electronics and battery cooling, with more than 500 W transport capabilities in gravity field. In conclusions, loop heat pipes will provide an energy efficient passive thermal control solution for next-generation low emission automotive, particularly for electric vehicles (EVs), which have high-level electrifications and more definitive cooling requirements.
1 September 2015 in Journal of Thermal Science and Engineering Applications
The convective thermal resistance which represents the heat removal from the heat sink surface of a heat pipe/heat sink module to mean coolant flow temperature is often a dominant contributor to the overall thermal resistance of a heat pipe/heat sink module or remote heat exchange (RHE). RHE is a thermal solution module composed of a heat spreader, thin flattened heat pipe with low profile heat sink which is widely used for the thermal management of compact portable electronic devices. Minimizing the convective thermal resistance at the heat sink of RHE as well as thickness reduction is often an important objective for the thermal designers. Recently, an alternate air mover system which operates based on piezoelectricity is developed. This device is called dual cooling jet (DCJ) in short which can be fabricated with very small thickness down to 1.0 mm. Thin DCJ as a synthetic jet generates air jet with more than 7 m/s air flow velocity which is promising for the increasing demands of thinner next generation portable electronic devices. DCJ is a promising device to dissipate the heat from the heat sink of a RHE. In this work, the performance of RHE is evaluated when heat is dissipated from its heat sink by DCJ. The results are compared with conventional rotary fan. The results show that more than 12 W of heat can be dissipated by DCJ which can easily compete with some commercialized rotary mini blowers while having much smaller thickness. Various configuration of heat sink–DCJ combinations as well as size and shape of both heat sink and DCJ are tested and based on thermal resistance data, cooling effectiveness of DCJ is studied.
17 March 2014 in Journal of Thermal Science and Engineering Applications
Modern consumer electronic trends point to a demand for thinner and more portable electronic devices. Conventional cooling systems of these portable electronic devices are challenging to miniaturize in thin profile applications that are typically on the order of several millimeters in thickness. In order to overcome some of these challenges, a synthetic jet, which is also considered as micro fluidic device, is developed. This device which operates based on Piezo electricity is called Dual Cooling Jet (DCJ). DCJ disturbs the boundary layer over a hot component and hence increases heat transfer compare to conventional blower. DCJ is typically defined as a device using a partially enclosed cavity with oscillating walls/diaphragms to create alternating suction and ejection of fluid across an interface or orifice. In this work, the results of cooling performance investigation of DCJ are shown and compared with natural convection cooling. Also, several experiments have been done to study the cooling effect of DCJ at different configuration with respect to heat source and the results are compared. At the end, the effects of heat source size is investigated which are helpful to understand how effective DCJ is when used for cooling several size chips. In addition, the results of this work show that DCJ can be combined with low profile heat sink as a promising next generation ultra thin thermal solution module.
26 August 2021 in Frontiers in Heat and Mass Transfer
A premiere free-access and peer-reviewed frontier journal site, serving the needs of the thermal-fluids community. See the latest research or submit an article. Quickly share your research with the global thermal-fluids community, for increased citations and impact at no cost.
1 January 2024 in Frontiers in Heat and Mass Transfer
Electrification of vehicles intensifies their cooling demands due to the requirements of maintaining electronics/electrical systems below their maximum temperature threshold. In this paper, passive cooling approaches based on heat pipes have been considered for the thermal management of electric vehicle (EV) traction systems including battery, inverter, and motor. For the battery, a heat pipe base plate is used to provide high heat removal (180 W per module) and better thermal uniformity (<5°C) for the battery modules in a pack while downsizing the liquid cold plate system. In the case of Inverter, two phase cooling system based on heat pipes was designed to handle hot spots arising from high heat flux (~100 W/cm)–for liquid cooling and provide location independence and a dedicated cooling approach-for air cooling. For EV motors, heat pipe-based systems are explored for stator and rotor cooling. The paper also provides a glimpse of development on high-performance microchannel-based cold plate technologies based on parallel fins and multi-layer 3D stacked structures. Specifically, this work extends the concept of hybridization of two-phase technology based on heat pipes with single-phase technology, predominately based on liquid cooling, to extend performance, functionalities, and operational regime of cooling solutions for components of EV drive trains. In summary, heat pipes will help to improve and extend the overall reliability, performance, and safety of air and liquid cooling systems in electric vehicles.