This paper presents a new concept of the control strategy in prevention program for the airlines to prevent the injuries of passengers and crew members for transport aircraft. A twin-jet transport aircraft encountered severe clear-air turbulence at transonic flight in descending phase is the study case of the present paper. The nonlinear and unsteady flight controllability models based on flight data mining and the fuzzy-logic modeling of artificial intelligence technique, are utilised to support this new concept. The proposed flight controllability models with the function of nonlinear dynamic inversion are employed to provide flight control strategy through flight simulations of dynamic inversion process; it is an innovation in mathematical modelling of aerospace engineering. Since the sudden plunging motion with the abrupt change in attitude and gravitational acceleration (i.e. the normal load factor) to affect the flight safety the most, hazard mitigation is a great concern for the aviation community. The present study is initiated to examine possible mitigation concepts of accident prevention to provide a training course for loss of control in-flight program to the airlines.
Total knee replacement is a common surgical procedure in orthopaedics. Accurate volumetric wear assessment of the polyethylene knee inserts has been an essential subject for improving the longevity. A new CMM-based methodology was presented to determine volumetric material loss based on curve surface fitting without prewear data, CAD model, or original design of drawings. Both computational and experimental simulated volume removal tests were run to validate the methodology by comparing with the gravimetric measurements. The volume and linear wear of the tibial inserts were calculated using the presented method based on the coordinates acquired by the CMM. The results indicate that the methodology is adequate for clinically retrieved tibial inserts where no prewear data are provided. This technique can also be used for biotribological study of other polyethylene components, since wear and damage can be assessed visually and volumetrically.
12 July 2018 in IOP Conference Series: Materials Science and Engineering
The surface topography of typical metal materials was analysed based on fractal theory. Six kind of metal materials were machined under the same turning parameters and the corresponding fractal dimension D of surface topography was calculated. The results indicate that the fractal dimension D can reflect the complexity of the surface morphology of metal materials; the fractal dimension D of ferrous metal materials is higher than nonferrous metal materials; no obvious linear relationship found between surface roughness Ra and fractal dimension D; fractal dimension D could reveal the intrinsic properties and the machinability of metal material with further analysis.
19 June 2018 in International Journal of Polymer Science
Ultrahigh molecular weight polyethylene (UHMWPE) bearings are used widely in orthopaedic joint replacement as a prominent material for improving the longevity, which is dramatically influenced by wear of polyethylene. Polyethylene tibial knee components from knee simulators under two different input conditions were analyzed using CMM and Micro-CT measurement techniques for volumetric loss with gravimetric measurement as reference. Based on the coordinates and image slices obtained, the surface curve fitting and image digitization methodology were used for the creation of nominal “original” surface in the case of no prewear data provided. The comparison results indicate that gravimetric remains the gold standard and the CMM measurement took less time and had better precision, accuracy, and repeatability compared to Micro-CT measurement technique.
The main purpose of this article is to present the nonlinear unsteady behaviour for jet transport aircraft response to serious atmosphere turbulence in cruise flight and to provide the appropriate mitigation concepts for pilots in the pilot training course of the IATA – Loss of Control In-flight (LOC-I) program. The flight data of a twin-jet and a four-jet transport aircraft encountered serious atmosphere turbulence are the study cases for this article. This study uses flight data mining and fuzzy-logic modeling of artificial intelligence techniques to establish nonlinear unsteady aerodynamic models. Since the rapid change of aerodynamic characteristics in turbulence, so the study uses decoupled longitudinal and lateral-directional motion to identify various eigenvalue motion modes of nonlinear unsteady behaviour through digital 6-DOF flight simulation. It is found that the changes of the main flight variables in the aerodynamic scene and flight environment of the two aircraft are different, but the profiles of five eigenvalue motion modes are actually similar. Those similar eigenvalue motion modes can formulate preventive actions related to the flight handling quality for safe and efficient control by pilots to execute the flight tasks. The one with a large drop height during the ups and downs motion between the two is chosen to construct the movement mechanism of nonlinear unsteady behaviours. The assessments of dynamic stability characteristics of nonlinear unsteady behaviour based on the approaches of oscillatory motion and eigenvalue motion modes related to loss of control will be demonstrated in this article. To develop preventive actions, the situation awareness response to the induced mutation of nonlinear unsteady behaviour on the pilot’s operations will be a further research task in the future.
5 November 2018 in IOP Conference Series: Materials Science and Engineering
The analysis of worn surface topography is an important approach to study the wear mechanism of friction pairs. The influence of mesh number of sand paper on simulated wear process was investigated based on fractal theory. The results indicate that cross-shear wear mode is appropriate for simulated wear, which is close to actual working condition and the resultant surface morphology has fractal characteristics. With the increase of the mesh number of sandpaper, the surface roughness Ra of stainless steel 0Cr18Ni9 and aluminum alloy 2A12 decreased while the fractal dimension D increased and showed a general linear relationship. However, the surface roughness Ra and fractal dimension D of the stainless steel were slightly greater than that of the aluminum alloy. Fractal dimension D may be related to the intrinsic physical properties of metallic materials and could be used to characterize the relative machinability of materials.