Chao Wu

Dr. Chao Wu


Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 July 2025 in Sensors
Verified
Journal Article
Open access
PDF file
QZQian Zhu
Qian Zhu
WZWenjie Zhang
Wenjie Zhang
WZWencheng Zhu
Wencheng Zhu
CWChao Wu
Chao Wu
JSJianping Shi
Jianping Shi
Microwave energy is ideal for wearable devices due to its stable wireless power transfer capabilities. However, rigid receiving antennas in conventional RF energy harvesters compromise wearability. This study presents a wearable system using a flexible dual-band antenna (915 MHz/2.45 GHz) fabricated via conformal 3D printing on arm-mimicking curvatures, minimizing bending-induced performance loss. A hybrid microstrip–lumped element rectifier circuit enhances energy conversion efficiency. Tested with commercial 915 MHz transmitters and Wi-Fi routers, the system consistently delivers 3.27–3.31 V within an operational range, enabling continuous power supply for real-time physiological monitoring (e.g., pulse detection) and data transmission. This work demonstrates a practical solution for sustainable energy harvesting in flexible wearables.

14 May 2025 in Energies
Verified
Journal Article
Open access
PDF file
ZLZhuopei Lv
Zhuopei Lv
XCXinbo Chai
Xinbo Chai
FWFuyin Wei
Fuyin Wei
HYHongkai Yang
Hongkai Yang
CWChao Wu
Chao Wu
JSJianping Shi
Jianping Shi
This work investigates the design of liquid-cooled heat sinks for IGBT modules via optimizing the Triple Periodic Minimal Surface (TPMS) structure. The performance of heat sinks with different porosity TPMS structures was compared through the finite element simulation software Fluent. The results indicate that smaller porosity is conducive to improving the heat dissipation efficiency, but the difference in pressure between the entrance and exit increases. The field-driven design method is further adopted to adjust the porosity according to the temperature field distribution, and the TPMS channel structures were optimized by nTopology software. The results show that the optimized Schwarz P, Gyroid, and Diamond structures have a comparable effect on reducing the maximum surface temperature as that of TPMS structures with uniform porosity; however, the differential pressure at the inlet and outlet decreased remarkably by 94.8%, 90.8%, and 88.9%, respectively, compared to the structure with a uniform porosity of 0.32. The Nusselt numbers of the optimized Gyroid and Diamond structures increased by 19.2% and 12.3%, respectively, compared to their structures with a uniform porosity of 0.84. This study illustrates the advantages of the field-driven design in enhancing the heat dissipation and reducing pressure loss, which provides an effective design solution for the heat dissipation of IGBT modules.

29 August 2026 in Energies
Verified
Journal Article
Open access
PDF file
RHRuiQuan Hu
RuiQuan Hu
JSJianping Shi
Jianping Shi
CWChao Wu
Chao Wu
YXYiming Xia
Yiming Xia
SXSongchang Xu
Songchang Xu
SCShuang Cai
Shuang Cai
Non-uniform heat flux in high-power electronic devices can induce local hotspots. To address hotspot thermal management, a hybrid microchannel heat sink featuring micro pin-fins with secondary channels (MPSCs) is proposed. Straight microchannels are used in the low-heat-flux region, while staggered pin-fins are arranged in the central hotspot region. Five models are considered: solid pin-fins without secondary channels (M1) and pin-fins with one-, three-, four-, and six-directional secondary channels (M2–M5). Over Re = 200–800, the thermal resistance of M3 is reduced by up to 43.3% compared with the SPMS, and the maximum PEC reaches 1.178. MPSC structures achieve better cooling at lower pumping power. At similar pumping power, the thermal resistance of M3 is 36.8% lower than the minimum value attainable by the SPMS. However, the marginal reduction in thermal resistance gradually weakens as the pumping power increases. The effects of hotspot heat flux and relative pin-fin height are investigated. MPSCs can withstand higher heat loads. Under a hotspot heat flux of 800 W/cm2, the maximum temperature of M3 remains below the safety threshold. Relative pin-fin height has a coupled effect on the thermal–hydraulic performance. At Re = 800, the PEC of M3 at RPH = 0.9 is about 2.8% higher than that at RPH = 1.0, and a PEC fitting equation is developed. The results show that the hybrid micro pin-fin heat sink with secondary channels disrupts the thermal boundary layer through internal flow diversion and local disturbance, thereby balancing hotspot suppression and pressure drop control. This design provides a reference for hotspot thermal management and thermal–hydraulic optimization of microchannel heat sinks.