This study proposes an improved microcombustor with a rectangular rib to improve the temperature level of the combustor wall. Moreover, the OH mass fraction, temperature distribution, and outer wall temperature of the original and improved combustors of premixed hydrogen/air flames are numerically investigated under various inlet velocities and equivalence ratios. Results show that the improved microcombustor enhances heat transfer between the mixture and wall because its recirculation zone is larger than that of the original, thereby resulting in high wall temperature. Conversely, thermal resistance in the horizontal direction increases with upstream and downstream step lengths. Consequently, the outer wall temperature decreases with step length in the improved combustor. A high equivalence ratio (e.g., 0.6) may result in the destruction of the combustor because the wall temperature has exceeded the acceptable temperature of wall material quartz. Therefore, the improved microcombustor is recommended for micro-thermo-photovoltaic systems.
1 August 2019 in Journal of Central South University
With the aim of increasing the momentum jet and obtaining better environmental adaptability, this study designs a new type of actuator combining a sparkjet actuator and a combustion-driven actuator. Numerical simulation shows that the combustion-driven sparkjet actuator has a higher velocity and mass rate compared to the sparkjet actuator when the length and orifice diameter are 6.5 mm and 1.3 mm, respectively, while the saturation work frequency is almost the same. A parameter study shows that as the volume increases, the pressure, orifice velocity, and mass rate of the combustion-driven sparkjet actuator increase. By contrast, the saturation work frequency decreases. Moreover, as the orifice diameter decreases, the orifice peak velocity, temperature, and pressure increase, whereas the mass flow rate and saturation work frequency decrease.
To increase the jet momentum and improve the environmental adaptability, a combustion-driven SparkJet actuator with a Laval-configured outlet is proposed to improve the performance of the actuator. Numerical simulation results show that, compared to straight outlet combustion-driven actuators with outlet diameters of 2 mm and 2.8 mm, the maximum jet velocity of the Laval-configured actuator increases by approximately 100 m/s and 350 m/s, separately. while the peak times decrease by about 50% and 12%, respectively. The work frequency of the Laval-structured combustion-driven actuator is 1333 Hz, which is higher than the 1176 Hz of the straight-tube-structured combustion-driven actuator with an outlet diameter of 2 mm. The Laval configuration effectively improves the working performance of the actuator. As the equivalence ratio increases from 0.6 to 1, the actuator’s jet velocity increases by approximately 65 m/s and 311 m/s, respectively, and its maximum combustion temperature is raised from 2700 K to 3000 K. The saturation work frequency is nearly the same. The pressure and jet mass flow rate in the actuator drop as the atmospheric pressure declines, while the combustion-driven actuator still exhibits high working performance when the atmospheric pressure is low. The maximum outlet velocity, Mach number, pressure, and temperature increase by about 20%, 13%, 25%, and 6%, while the peak time increases by about 40% as the ignition position moves from the middle position to a 2.8 mm displacement toward the outlet.
Active flow control actuators are critical for improving aerodynamic performance in applications such as aircraft lift enhancement, drag reduction, and maneuverability improvement. However, the plasma synthesis jet actuator (PSJA) is limited by the constraints of electric energy deposition, making it difficult to further improve the jet velocity and mass flow rate. Meanwhile, the jet velocity driven by combustion needs to be further increased. This study preliminarily investigated the characteristics of a combustion-driven SparkJet actuator through experiments; a combustion-driven SparkJet actuator integrates the advantages of plasma actuators and combustion-driven actuators. The actuator employs a continuous methane–air mixture supply ignited by spark discharge. High-speed shadowgraph imaging is used to characterize the jet flow field evolution. The effects of the cavity volume, normalized outlet diameter (d* = d/h), and equivalence ratio on jet performance are systematically examined. As the normalized outlet diameter increases from 0.666 to 1, the jet penetration distance and jet width increase with an increasing normalized outlet diameter, owing to the reduced boundary layer blockage effect at the orifice. However, when the normalized outlet diameter equals 1, both the jet penetration distance and jet width first increase and then decrease with increasing cavity volume; hence, the outlet diameter and cavity have an optimal size. At an equivalence ratio of mixture ≤1, increasing the methane flow rate enhances the volumetric chemical heat release rate, thereby monotonically improving the jet width and penetration distance. The combustion-driven actuator demonstrates a significantly higher jet velocity compared to a conventional plasma actuator under identical geometric parameters; the combustion reaction can effectively amplify the jet energy and velocity of the actuator. Moreover, the combustion-driven SparkJet actuator also has the same working frequency when the actuator volume is the same, indicating that the combustion process does not significantly extend the cycle time. The maximum jet velocity first increases and then decreases with increasing cavity volume; the reason that the maximum jet velocity first increases is that a larger volume results in a greater mixture mass and more released heat; it then decreases due to incomplete combustion occurring in large chambers. These results show that the design standards for the combustion-driven actuator are fundamentally different from those for the plasma actuator, and their optimal performance is related to not only electrical energy density but also combustion performance. The design parameters of the combustion-driven actuator can be optimized to maximize the jet front velocity. The experimental data in this article provides a reference for optimizing the performance of combustion-driven actuators.