Films combining hydroxyapatite (HA) with minute amounts (ca. 1 weight %) of (rhenium doped) fullerene-like MoS2 (IF) nanoparticles were deposited onto porous titanium substrate through electrophoretic process (EPD). The films were analyzed by scanning electron microscopy (SEM), X-ray diffraction and Raman spectroscopy. The SEM analysis showed relatively uniform coatings of the HA + IF on the titanium substrate. Chemical composition analysis using energy dispersive X-ray spectroscopy (EDS) of the coatings revealed the presence of calcium phosphate minerals like hydroxyapatite, as a majority phase. Tribological tests were undertaken showing that the IF nanoparticles endow the HA film very low friction and wear characteristics. Such films could be of interest for various medical technologies. Means for improving the adhesion of the film to the underlying substrate and its fracture toughness, without compromising its biocompatibility are discussed at the end.
Nanoparticles of transition metal dichalcogenides (TMDC) have been known to reduce friction and wear when added to oil-type liquid lubricants. Aggregation limits the ability of the nanoparticles to penetrate into the interface between the two rubbing surfaces—an important factor in friction reduction mechanisms. Doping has been successfully used to reduce agglomeration, but it must be done in the production process of the nanoparticles. The use of surface-functionalized nanoparticles is less common than doping. Nonetheless, it has the potential to reduce agglomeration and thereby improve the reduction of friction and wear. In this study, we present the results of preliminary tribological ball-on-flat tests performed with WS2 nanoparticles functionalized by a humin-like conformal shell, as additives to polyalphaolefin-4 (PAO-4) oil. We tested WS2 inorganic nanotubes (INTs) and two grades of inorganic fullerene-like nanoparticles (IFs). The shell/coating was found to improve friction reduction for IFs but not for INTs through better dispersion in the oil. The thicker the coating on the IFs, the less agglomerated they were. Coated industrial-grade IFs were found, by far, to be the best additive for friction reduction. We suggest the combination between reduced agglomeration and poor crystallinity as the reason for this result.
The main goal of the presented work was the analysis of the interaction between deformed microstructures and friction and the wear properties of four face centered cubic (fcc) metals. Pure fcc metals such as Ag, Cu, Ni, and Al with different values of stacking fault energy (SFE) were chosen for pin-on-disk tests in lubricated conditions. Friction properties of the four fcc metals are presented herein as their Stribeck curves. The transition from elasto-hydrodynamic lubrication (EHL) to boundary lubrication (BL) regions depends mainly on the values of SFE, hardness, and contact temperature. The acoustic emission (AE) parameters were analyzed in the transition from the EHL to the BL region. The models of friction in different lubricant conditions related to the AE waveforms were proposed. The nanocrystalline top surface layers characterized the deformed structure during friction of Ag in the BL region. The lamellar cross-sectional microstructure was formed in the subsurface layers of Ag, Cu, and Ni in the friction direction. Steady state friction and wear in the BL conditions were explained by a balance between the hardening and the dynamic recovery, which was strongly dependent on the SFE and the temperature. The interaction between the deformed structure, the friction, and the wear properties of the studied metals rubbed in the BL region is discussed herein.
This work aims to demonstrate the discrepancy between the results achieved in the application of ball-on-flat devices. Meanwhile, the interaction between contact parameters and the morphology of friction surfaces will be considered. Flattening depends on the mechanical properties of contact materials and the variation in the deformed structure in surface layers. To evaluate the interaction between roughness parameters and contact pressure, wear, and morphology of the surfaces, a ball-on-disk rig was applied. The average groove sizes were measured on micro- and macroscales. The relation between groove sizes on micro- and macro scales is close to the same. The flattening sinusoidal ball-on-flat model was considered. The real friction and wear tests were used to analyze plastic deformation by accounting for dislocation gliding and the interaction between neighboring asperities. The relation of shear stresses to the interference of rough asperities was established. The effective plastic strain gradient was evaluated. The formation of a highly effective plastic strain gradient is associated with a high dislocation density. The effect of dislocation density on the hardening–softening of surface layers is considered.
Inorganic nanotubes (INTs) and fullerene-like nanoparticles (NPs) of WS2/MoS2 penetrate and exfoliate at the contact interface and facilitate tribofilm formation. While the tribological properties are greatly improved by exfoliated NPs that shed easily, they may be diminished by agglomeration in oil. Therefore, surface functionalization is employed to improve dispersion in oil-based suspensions. Here, WS2 INTs were functionalized by polytetrafluoroethylene (PTFE) in a simple and cost-effective bath sonication method. WS2-INTs with two concentrations of added PTFE were characterized by scanning and transmission electron microscopy, micro-Raman spectroscopy, and thermogravimetric analysis. Superior distribution of WS2 was observed before and during friction experiments. Chemical analysis showed a significantly greater amount of PTFE-coated INTs on rubbed surfaces, in accordance with the improved friction and wear properties.