Ferromagnetic-antiferromagnetic (FM-AFM) bilayer dynamics have been a recent topic of interest due to the interaction occurring at the interface, where the magnetic moments of the AFM can be imprinted into the FM, and the exchange bias field can affect these dynamics. Here, we investigate permalloy () and (/) hybrids and for comparison single films in the broad thickness range varied from few nm to 200 nm by using static (Kerr effect) and dynamic (spin-wave) measurements along with micromagnetic simulations. We observe hybrid modes between uniform (ferromagnetic resonance FMR, ) and perpendicular standing spin waves (PSSWs, , 2) and a clear enhancement of the PSSW mode frequencies upon interfacing with both from experiments and simulations. This enhancement becomes less pronounced as the thickness of the film increases, demonstrating its interfacial origin rooted in the exchange coupling between the FM and AFM layers. Besides, through micromagnetic simulations, we investigate and correlate changes in spatial profiles of the PSSWs with the interfacial exchange coupling. As the thickness is increased, we see that the and modes begin to couple with the fundamental FMR mode, resulting in asymmetric (with respect to the layer center) modes. Our results suggest that PSSW detection in a ferromagnet offers a means of probing the interfacial exchange coupling with the adjacent AFM layer. Furthermore, the controlled spatial symmetry breaking by the AFM layer enables engineering of PSSWs with different spatial profiles in the FM.
Antiferromagnetic/ferromagnetic (AF/F) systems have been extensively investigated due to the importance that interfacial exchange coupling effects have in the development of magnetic storage technologies. Recently, these systems have garnered interest for the potential they have to imprint the magnetic moments of the AF into an F layer, offering the possibility of using it as a read-out mechanism in antiferromagnetic spintronics. In this study, we explored the importance of crystalline orientation and strains induced by the substrate in the exchange coupling properties of NiO/FeCo AF/F bilayers. For that, we have grown NiO/FeCo bilayers on MgO (001) and Al2O3 (0001) substrates varying the FeCo layer thickness. In addition, we have analyzed both deposited samples and those with induced interfacial unidirectional anisotropy. For inducing such interfacial anisotropy, we used a field cooling procedure, heating the bilayers to 650 K and subsequently cooling down to room temperature under the presence of an external magnetic field of 300 mT. We have investigated the effect of the substrate in terms of crystalline orientation and lattice mismatching on the AF/F exchange coupling as well as the dependence of the coercivity and exchange bias on the inverse F layer thickness that is consistent with the interfacial origin of the AF/F exchange coupling. Moreover, the angular dependence of the magnetic properties was explored by using vectorial Kerr magnetometry, confirming the presence of both magnetocrystalline anisotropy, arising from the epitaxial character of the growing process mainly when the bilayer is grown on MgO (001) substrates, and the field cooling (FC)-induced unidirectional anisotropy.
Understanding the interactions in hybrid systems based on graphene and functional oxides is crucial to the applicability of graphene in real devices. Here, we present a study of the structural defects occurring on graphene during the early stages of the growth of CoO, tailored by the electronic coupling between graphene and the substrate in which it is supported: as received pristine graphene on polycrystalline copper (coupled), cleaned in ultra-high vacuum conditions to remove oxygen contamination, and graphene transferred to SiO2/Si substrates (decoupled). The CoO growth was performed at room temperature by thermal evaporation of metallic Co under a molecular oxygen atmosphere, and the early stages of the growth were investigated. On the decoupled G/SiO2/Si samples, with an initial low crystalline quality of graphene, the formation of a CoO wetting layer is observed, identifying the Stranski-Krastanov growth mode. In contrast, on coupled G/Cu samples, the Volmer-Weber growth mechanism is observed. In both sets of samples, the oxidation of graphene is low during the early stages of growth, increasing for the larger coverages. Furthermore, structural defects are developed in the graphene lattice on both substrates during the growth of CoO, which is significantly higher on decoupled G/SiO2/Si samples mainly for higher CoO coverages. When approaching the full coverage on both substrates, the CoO islands coalesce to form a continuous CoO layer with strip-like structures with diameters ranging between 70 and 150 nm.
Thin films of lithium spinel ferrite, LiFe5O8, have attracted much scientific attention because of their potential for efficient excitation, the manipulation and propagation of spin currents due to their insulating character, high-saturation magnetization, and Curie temperature, as well as their ultra-low damping value. In addition, LiFe5O8 is currently one of the most interesting materials in terms of developing spintronic devices based on the ionic control of magnetism, for which it is crucial to control the lithium’s atomic content. In this work, we demonstrate that dual ion beam sputtering is a suitable technique to tailor the lithium content of thin films of lithium ferrite (LFO) by using the different energies of the assisting ion beam formed by Ar+ and O2+ ions during the growth process. Without assistance, a disordered rock-salt LFO phase (i.e., LiFeO2) can be identified as the principal phase. Under beam assistance, highly out-of-plane-oriented (111) thin LFO films have been obtained on (0001) Al2O3 substrates with a disordered spinel structure as the main phase and with lithium concentrations higher and lower than the stoichiometric spinel phase, i.e., LiFe5O8. After post-annealing of the films at 1025 K, a highly ordered ferromagnetic spinel LFO phase was found when the lithium concentration was higher than the stoichiometric value. With lower lithium contents, the antiferromagnetic hematite (α-Fe2O3) phase emerged and coexisted in films with the ferromagnetic LixFe6-xO8. These results open up the possibility of controlling the properties of thin lithium ferrite-based films to enable their use in advanced spintronic devices.
In this study, we investigated the frictional properties of TiB2 films produced by high-power impulse magnetron sputtering and compared them with those of TiN- and CrN-sputtered coatings also made using high-power pulsed discharges. The films were characterised by scanning electron microscopy, Electron Probe Micro-Analysis, nanoindentation and friction tests. Sliding friction analyses were performed against aluminium surfaces at different temperatures, ranging from room temperature to 300 °C. The TiB2 coatings exhibited hardness values of about 39 GPa, regardless of the bias potential used between −50 V and −100 V, a low modulus of around 300 GPa and a dense compact columnar microstructure with grain sizes between 51 and 68 nm in diameter. The friction behaviour on aluminium produced the transfer of this element to the films, at rates that depended on the test temperature. The TiN and CrN coatings exhibited low–medium adhesion to aluminium at room temperature and severe transfer during the friction tests at 150 °C. In the case of the TiB2 films, the adhesion of aluminium during friction tests was low for temperatures up to 175 °C. In fact, a clear transition of the mild-to-severe adhesion of aluminium on TiB2 was observed in the temperature range of 175 °C to 200 °C for the testing conditions evaluated in this study, which was concomitant with the evolution observed for the friction coefficients.