The electrical energy from the sun can be extracted using solar photovoltaic (PV) modules. This energy can be maximized if the connected load resistance matches that of the PV panel. In search of the optimum matching between the PV and the load resistance, the maximum power point tracking (MPPT) technique offers considerable potential. This paper aims to show how the modelling process of an efficient PV system with a DC load can be achieved using a fuzzy neural network (FNN) controller. This is applied via an innovative methodology, which senses the irradiance and temperature of the PV panel and produces an optimal value of duty ration for the boost converter to obtain the MPPT. The coefficients of this controller have been refined based upon previous data sets using the irradiance and temperature. A gradient descent algorithm is employed to improve the parameters of the FNN controller to achieve an optimal response. The validity of the PV system using the MPPT technique based on the FNN controller is further demonstrated via a series of experimental tests at different ambient conditions. The simulation results show how the MPPT technique based on the FNN controller is more effective in maintaining the optimal power values compared with conventional techniques.

Prediction of solar irradiance plays an essential role in many energy systems. The objective of this paper is to present a low-cost solar irradiance meter based on artificial neural networks (ANN). A photovoltaic (PV) mathematical model of 50 watts and 36 cells was used to extract the short-circuit current and the open-circuit voltage of the PV module. The obtained data was used to train the ANN to predict solar irradiance for horizontal surfaces. The strategy was to measure the open-circuit voltage and the short-circuit current of the PV module and then feed it to the ANN as inputs to get the irradiance. The experimental and simulation results showed that the proposed method could be utilized to achieve the value of solar irradiance with acceptable approximation. As a result, this method presents a low-cost instrument that can be used instead of an expensive pyranometer.

The direct-current (DC) motor has been widely utilized in many industrial applications, such as a multi-motor system, due to its excellent speed control features regardless of its greater maintenance costs. A synchronous regulator is utilized to verify the response of the speed control. The motor speed can be improved utilizing artificial intelligence techniques, for example fuzzy neural networks (FNNs). These networks can be learned and predicted, and they are useful when dealing with nonlinear systems or when severe turbulence occurs. This work aims to design an FNN based on a model reference controller for separately excited DC motor drive systems, which will be applied in a multi-machine system with two DC motors. The MATLAB/Simulink software package has been used to implement the FNMR and investigate the performance of the multi-DC motor. moreover, the online training based on the backpropagation algorithm has been utilized. The obtained results were good for improving the speed response, synchronizing the motors, and applying load during the work of the motors compared to the traditional PI control method. Finally, the multi-motor system that was controlled by the proposed method has been improved where its speed was not affected by the disturbance.

The reliance on distributed renewable energy has increased recently. As a result, power electronic-based distributed generators replaced synchronous generators which led to a change in the dynamic characteristics of the microgrid. Most critically, they reduced system inertia and damping. Virtual synchronous generators emulated in power electronics, which mimic the dynamic behaviour of synchronous generators, are meant to fix this problem. However, fixed virtual synchronous generator parameters cannot guarantee a frequency regulation within the acceptable tolerance range. Conversely, a dynamic adjustment of these virtual parameters promises robust solution with stable frequency. This paper proposes a method to adapt the inertia, damping, and droop parameters dynamically through a fuzzy neural network controller. This controller trains itself online to choose appropriate values for these virtual parameters. The proposed method can be applied to a typical AC microgrid by considering the penetration and impact of renewable energy sources. We study the system in a MATLAB/Simulink model and validate it experimentally in real time using hardware-in-the-loop based on an embedded ARM system (SAM3X8E, Cortex-M3). Compared to traditional and fuzzy logic controller methods, the results demonstrate that the proposed method significantly reduces the frequency deviation to less than 0.03 Hz and shortens the stabilizing/recovery time.

This work deals with the simulation model of multi-machines system as cold rolling mill is considered as application. Drivers of rolling system are a set of DC motors, which have extend applications in factories as aluminum rolling. Interconnection of multi DC motors in such a way that they are synchronized in their rotational speed. In cold rolling, the accuracy of the strip exit thickness is a very important factors. To realize accuracy in the strip exit thickness, Automatic Gauge Control system is used. In this paper MATLAB/SIMULINK models are proposed and implemented for the entire structures. Simulation results were presented to verify proposed model of cold rolling mill