Sang Ho Lim

Dr. Sang Ho Lim


Research Focus & Metrics

Academic Career Length

43Years (1984-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2016 in Acta Materialia
Verified
Journal Article
Closed access
TKTae-Hoon Kim
Tae-Hoon Kim
SLSeong-Rae Lee
Seong-Rae Lee
SYSeok Jin Yun
Seok Jin Yun
SLSang Ho Lim
Sang Ho Lim
HKHyo-Jun Kim
Hyo-Jun Kim
TJTae-Suk Jang
Tae-Suk Jang

1 July 2005 in Wear
Verified
Journal Article
Closed access
DLD.-S. Lim
D.-S. Lim
DYD.-H. You
D.-H. You
HCH.-J. Choi
H.-J. Choi
SLSang Ho Lim
Sang Ho Lim
HJH. Jang
H. Jang

1 January 1999 in Journal of Magnetism and Magnetic Materials
Verified
Journal Article
Closed access
SLSang Ho Lim
Sang Ho Lim
SKS.R. Kim
S.R. Kim
SKS.Y. Kang
S.Y. Kang
JPJ.K. Park
J.K. Park
JNJ.T. Nam
J.T. Nam
DSDerac Son
Derac Son

1 January 2011 in Journal of Applied Physics
Verified
Journal Article
Closed access
SJSoo Young Jang
Soo Young Jang
CYChun-Yeol You
Chun-Yeol You
SLSang Ho Lim
Sang Ho Lim
SLS. R. Lee
S. R. Lee
The changes in the magnetic dead layer (MDL) and saturation magnetization of the CoFeB layers are investigated as a function of the annealing temperature for four different unit structures, that are relevant to the synthetic ferrimagnetic free structure in MgO-based magnetic tunnel junctions. The MDL results for these unit structures are then converted into those for the constituent interfaces of the free structure. Most of the changes in the MDL thickness occur during annealing at a low temperature of 150 °C while those in the saturation magnetization occur at a high annealing temperature of 350 °C. These results for the MDL and saturation magnetization are critically tested by using the synthetic ferrimagnetic free structures with various thickness asymmetries. The observed switching properties of these tested structures are in good agreement with those expected from the results for the MDL and saturation magnetization, confirming the accuracy of the present results. The accuracy of the saturation magnetization is further confirmed by ferromagnetic resonance experiments.

19 January 2018 in Scientific Reports
Verified
Journal Article
Open access
PDF file
HGHyung Keun Gweon
Hyung Keun Gweon
SYSeok Jin Yun
Seok Jin Yun
SLSang Ho Lim
Sang Ho Lim
The perpendicular magnetic anisotropy (PMA) properties of Pt/Co/MgO trilayers are investigated as a function of the MgO sputtering power (PMgO) and its thickness (tMgO), both of which are important parameters affecting the degree of oxygen interpenetration into Co during sputtering. A strong PMA is achieved at small values of PMgO and tMgO, where the oxygen interpenetration into Co is expected to be small. The range of oxygen interpenetration is relatively extended in such a way that it affects both the Pt/Co and Co/MgO interfaces. The PMA properties of as-deposited samples are improved by post-annealing for temperatures up to 400 °C examined in this study, probably due to the diffusion of the interpenetrated oxygen atoms toward the Co/MgO interface. In a structure of Pt/Co (0.6 nm)/MgO (2 nm), which is fabricated at PMgO = 50 W and then annealed at 400 °C, a huge saturation field is achieved (over 40 kOe) indicating a very strong PMA. Between the two interfaces of Pt/Co and Co/MgO, the PMA is mainly due to the former in the as-deposited state, but the contribution of the latter increases with the increase in the annealing temperature.

9 June 2008 in Applied Physics Letters
Verified
Journal Article
Closed access
PDF file
DLD. H. Lee
D. H. Lee
SLSang Ho Lim
Sang Ho Lim
Three-dimensional numerical calculations based on the finite element method are performed to calculate the increase of temperature caused by Joule heating during the current-induced magnetization switching of an MgO-based magnetic tunnel junction. The increase of temperature is found to be significantly large (the maximum being 145K ) at critical conditions for the current-induced magnetization switching. The temperature increase also differs greatly, depending on the critical condition, requiring a correction in calculating the thermal stability parameter using the Slonczewski equation. After the correction, the thermal stability parameter increases substantially from 67 to 76.