In engineering practice, liquid droplet impingement typically occurs at an oblique angle relative to the target surface, yet the influence of impact orientation on damage outcomes remains contentious and exhibits target-material dependency. In this paper, a typical single-waterjet-generating technique is applied to liquid impact tests on a unidirectional carbon fiber-reinforced polymer (CFRP) laminate, with special focus on the effects of the impingement angle and the fiber orientation. Finite-element simulation is employed to help reveal the failure mechanism of oblique impacts. The results show that, in most cases, the damage caused by a 15° oblique impact is slightly larger than that of a normal impact, while the increase amplitude varies with different impact speeds. Resin removal is more prone to occur when the projection of the waterjet velocity on the impact surface is perpendicular (marked as the fiber orientation PE) rather than parallel (marked as the fiber orientation PA) to the fiber direction of the top layer. A PE fiber orientation can lead to mass material peeling in comparison with PA, and the damage range is even much larger than for a normal impact. The underlying mechanism can be attributed to the increased lateral jet-particle velocity and resultant shear stress along the impact projection direction. The distinct damage modes observed on the CFRP laminate with the different fiber orientations PE and PA originate from the asymmetric tensile properties in the longitudinal/transverse directions of laminates coupled with dissimilar fiber–matrix interfacial characteristics. A theoretical model for the surface damage area under a single-jet impact was established through experimental data fitting based on a modified water-hammer pressure contact-radius formulation. The model quantitatively characterizes the influence of critical parameters, including the jet velocity, diameter, and impact angle, on the central area of the surface failure ring.
1 May 2026 in Journal of Physics: Conference Series
STF (shear thickening fluid) impregnated fabric, with potential application in ballistic armour, has been numerically studied, with little consideration given to the enhancement effect of silica agglomerations. This paper carries out modelling and simulation research on STF-impregnated plain woven fabric. The detailed meso-structure models are constructed, where woven fabric and silica agglomerations of STF are established separately according to realistic geometric structures. The meso-structure models are validated by experiments. The impact processes are studied to identify the enhancement of STF agglomerations. The mass fraction of silica agglomerations and the impact velocity are varied to investigate their effects on shielding performance. The critical mass fraction is found for the least energy absorption capacity. The enhancement works when silica agglomerations collide with each other at a large enough mass fraction. The energy absorption capacity of the woven fabric decreases as the impact velocity increases.
Trans-medium vehicles, including supercavitating torpedoes, submarine-launched projectiles, and high-speed hydroballistic bodies, demonstrate increasingly diverse applications in crossing the air–water interface. For such vehicles, the truncated-cone (flat-headed) configuration represents a geometry of significant engineering relevance, as it is widely adopted in the nose sections of supercavitating projectiles and certain underwater ballistic penetrators where the flat head promotes rapid vaporization and cavity generation during high-speed water entry. The air-to-water transition process typically generates extreme hydrodynamic impact loads due to complex multiphase flow and fluid–structure coupling interactions, with water compressibility playing a significant role under hydroballistic conditions. This study focuses on the water-entry regime at velocities ranging from 300 to 1100 m/s, corresponding to hydroballistic speeds relevant to supercavitating vehicles (e.g., the Shkval torpedo operates at approximately 370 m/s) and the initial impact phase of high-speed trans-medium projectiles. Parametric studies are conducted with varying entry velocities (Mach 0.20~0.73 in water), impact angles, and structural dimensions to systematically investigate their effects on the peak slamming overload, using a dynamic mesh technique coupled with a VOF multiphase model with compressibility effects for both air and water phases. The results demonstrate that compressibility effects induce a pronounced air cushion effect during water impact, wherein compression waves generated during high-speed entry dominate the load formation process. Velocity is identified as the most sensitive factor affecting peak overload, followed by structural size parameters. The findings provide valuable guidance for the protective design of high-speed water-entry structures operating in the hydroballistic regime.