Drag reduction has constantly received great attention due to its extensive range of applications in fluid transportation and vehicle industries. The vital role of two different additive and non‐additive techniques (polymer additives and superhydrophobic surfaces) to reduce the drag force experienced by underwater vehicles, fluid flow through pipes, ducts, open or closed channels, and other wall‐bounded laminar and turbulent flows is highlighted. Reducing the drag resistance can significantly enhance the performance of immersed vehicles and results in saving the energy consumed on a large scale. The progress in theoretical modeling, experimental and computational studies of both techniques are reviewed, together with the surface design, wettability, and influence of the roughness factor of superhydrophobic surfaces and the effect of polymer drag‐reducing agents for wall‐bounded flows and multiphase flows. General formulations, potential applications, and major issues involved in the aforementioned approaches are summarized.
Phase change material (PCM) is one of the most important ways to store and manage energy. The melting process of PCM in a rectangular enclosure with the different aspect ratio is frequently related to some thermal energy storage devices. In this work, the melting of PCM in the horizontal rectangular enclosures heated from the different sides and the influence of aspect ratio of the rectangle are carefully studied. The enthalpy porosity technique and the finite volume method (FVM) are used to simulate the melting process numerically. The results show that the melting process of PCM can be dominated by conduction or natural convection due to the different heated sides. The melting of PCM in the enclosure heated from the bottom side is firstly affected by conduction and then mostly influenced by convection. In addition, the aspect ratio of the rectangular enclosure is found to play an important role in the melting process. Finally, a series of fitting correlations of the liquid fraction, Nusselt number and the energy storage are presented with the influence of aspect ratios in order to provide the reference for designing the rectangular container of PCM. This study is helpful for the selection of an appropriate aspect ratio and heating method to achieve the desired energy storage performance of encapsulated PCM.
Honeycomb structure with phase change material (PCM) is frequently used in passive thermal management devices. The geometrical shape of the honeycomb core greatly influences the melting rate of the PCM. This paper investigates the melting rates of PCM in honeycomb cores of non-hexagonal cells in comparison with that of hexagonal cell in three Rayleigh numbers. The objective is to find the optimal shape in order to reduce the melting time of the PCM. The constrained melting behaviors of PCM in triangular, quadrilateral, hexagonal, and circular honeycomb cores are numerically studied. The enthalpy porosity technique and finite volume method are used in this paper. The instantaneous liquid fraction and energy absorption of PCM in different honeycomb cores are discussed in detail. The influences of the placed orientation and aspect ratio of different cores on melting rates of PCM are considered. Results show that the melting rate of PCM in a rectangular core is always higher than the hexagonal core for the given aspect ratio and Rayleigh number. The geometrical factor (GF), which indicates the cross-sectional area per unit perimeter, is found to be an important index on the melting rate. At a small Rayleigh number, it takes a longer melting time of the PCM for the core with a larger GF. As the Rayleigh number is large, the melting time of the PCM is affected by both the GF and the orientation of the cores.
1 January 2021 in International Journal of Micro Air Vehicles
For micro air vehicles (MAV), the precise prediction of aerodynamic force plays an important role. The aerodynamic force of a comparative low Reynold number (Re) vehicle tends to be affected by the different flow modes. In this paper, the aerodynamic performance of a three-dimensional NACA0012 airfoil is studied numerically. A range of angles of attack (α) 0°−25° and Reynolds number 1000 is considered. Mean and fluctuating coefficients of aerodynamic forces around NACA0012 airfoil are analyzed for different wake modes. The difference of aerodynamic forces between two and three-dimensional simulations are compared. The results show that the wake remains steady two-dimensional for lower angles of attack. At α = 9°, Von Karman vortex pattern is noticed. Flow transition to three-dimensional as the angle of attack increases from α = 13°. 3D wake is found to be stable with parallel shedding mode for 14°-17°. However, these modes become finer with the gradual increase in angle of incidence. While, wake loses its three-dimensional stability to chaotic with gradual increment in angle of attack afterwards.
The propulsion of a pitching flexible plate in a uniform flow is investigated numerically. The effects of bending stiffness ( $K$ ), pitching amplitude ( $A_L$ ) and frequency ( $St$ ) on the wake patterns, thrust generations and propulsive performances of the fluid–plate system are analysed. Four typical wake patterns, i.e. von Kármán, reversed von Kármán, deflected and chaotic wakes, emerge from various kinematics, and the $St-A_L$ wake maps are given for various $K$ . The drag-to-thrust transitions (DTT) and the wake transitions (WT) between the von Kármán and reversed von Kármán wakes are examined. Results indicate that the WT and DTT boundaries can be scaled by the chord-averaged distance of travel, $\mathcal {L}$ , which leads to $\mathcal {L}\times St \approx 1$ and $\mathcal {L}\times St \approx 1.2$ , respectively. Further, the resonance mechanism for the performance enhancement is revealed and confirmed in a wide range of parameters. The dimensionless average speed of plate, $\mathcal {U^*}\left (=\mathcal {L}\times St\right )$ , is adopted merely to characterize the propulsive performances. For the first time, the $\mathcal {U^*}$ -based scaling laws for the thrust and power are revealed in pitching rigid and flexible plates for various $A_L$ and $St$ . This study may deepen our understanding of biological swimming and flying, and provide a guide for bionic design.
Dynamics of two-dimensional flow past a rigid flat plate with a trailing closed flexible filament acting as a deformable afterbody are investigated numerically by an immersed boundary-lattice Boltzmann method for the fluid flow and a finite element method for the filament motion. The effects of Reynolds number ( $Re$ ) and length ratio ( $Lr$ ) on the flow patterns and dynamics of the rigid-flexible coupling system are studied. Based on our numerical results, five typical state modes have been identified in $Lr\unicode{x2013}Re$ plane in terms of the filament shape and corresponding dynamics, i.e. static deformation, micro-vibration, multi-frequency flapping, periodic flapping and chaotic flapping modes, respectively. Benefiting from the passive flow control by using the flexible filament as a deformable afterbody, the coupled system may enjoy a significant drag reduction (up to $22\,\%$ ) compared with bare plate scenarios ( $Lr=1$ ). Maximum drag reduction achieved at $L_{c,{min}} \in [1.8, 2]$ is often accompanied by the onset of the system state transition. The flow characteristic and its relation to the change in hydrodynamic drag are further explored in order to reveal the underlying mechanisms of the counterintuitive dynamical behaviour of the coupled system. The scaling laws for the form drag and the friction drag, which arise from the pressure and viscous effects, respectively, are proposed to estimate the overall drag acting on the system. The results obtained in the present study may shed some light on understanding the dynamical behaviour of rigid-flexible coupling systems.