The present work is dedicated to the study of multiphase turbulent and three-dimensional rotational flow in dust cyclones, a contribution to air pollution control. Cyclones are widely used devices for the separation of constituents from solid-gas mixtures in industry. In order to improve the filtration efficiency of cyclones, and to reduce the pressure drop, parametric numerical simulation studies using the Fluent code have been conducted to characterise the effects of the parameters affecting the operation of these devices through their performance indicators. In this work, the effect of inlet velocity and the particle size on the turbulent flow air in the cyclone is presented. Numerical simulation of the flow by Fluent code using three numerical models: the first based on the dissipation of kinetic energy by viscosity (RNG) K-epsilon and standard K-epsilon as well as the last based on the solution of Reynolds stress equations (RSM), combined with the multiphase mixing model, gave interesting results in terms of the pressure and flow field in the separator, the variation of inlet velocity, and the variation of particle size. Validation with experimental and empirical results showed the advantage of the Reynolds stress turbulence model (RSM) over the standard K-epsilon and RNG K-epsilon. The RSM model better captures physical phenomena in an intense vortex flow in the presence of walls. But it is characterised by a very long calculation time and requires large machine resources. An alternative to this model is RNG K-epsilon model, which offers a reasonable calculation time with acceptable results (maximum deviation of 5 ) for speed values below 10 m/s. In the absence of numerical resources, certain empirical models such as those of First (for the evaluation of pressure drop) and Iozia and Leith (for evaluation of efficiency) may well be useful for the dimensioning of the cyclone.

Many experiments have been done by authors to study the influence of the natural ventilation through openings on fire behaviour in compartments. It has been revealed that fire will be influenced by the size of existing openings which can be an open window, an open door, or both of them. Concerning the last case, the literature does not give any information about the impact of the arrangement of these openings on the behaviour of fire. The present paper aims then to carry out a comparative study of the disposition of the window compared to the door, on the behaviour of fire in a compartment. To achieve that objective, fire experiments were conducted in a reduced scale room of ​​dimensions 1.20 m × 1.20 m × 1.02 m, which can be modulated into two configurations. The first one named “PFC configuration” is the case where the open door and the open window are in nonopposite walls. The second one named “PFO configuration” is the case where these both openings are in opposite walls. After having performed several fire tests in both configurations using the same amount of diesel fuel as fire source, results revealed that the fuel burns faster in the PFC configuration compared to that in the PFO configuration. This is due to a global mass loss rate of 2.93×10−4kg.s−1 against2.62×10−4kg.s−1, respectively. Beyond a difference of 20°C observed on the maximal temperature of burned gases located at ceiling, results also revealed the production of ghosting flames in the PFO configuration.

We have developed a curved finite element for a cylindrical thick shell based on the thick shell equations established in 1999 by Nzengwa and Tagne (N-T). The displacement field of the shell is interpolated from nodal displacements only and strains assumption. Numerical results on a cylindrical thin shell are compared with those of other well-known benchmarks with satisfaction. Convergence is rapidly obtained with very few elements. A scaling was processed on the cylindrical thin shell by increasing the ratioχ=h/2R(half the thickness over the smallest radius in absolute value) and comparing results with those obtained with the classical Kirchhoff-Love thin shell theory; it appears that results diverge at2χ=1/10=0.316because of the significant energy contribution of the change of the third fundamental form found in N-T model. This limit value of the thickness ratio which characterizes the limit between thin and thick cylindrical shells differs from the ratio 0.4 proposed by Leissa and 0.5 proposed by Narita and Leissa.

To meet more stringent norms and standards concerning engine performances and emissions, engine manufacturers need to develop new technologies enhancing the nonpolluting properties of the fuels. In that sense, the testing and development of alternative fuels such as biodiesel are of great importance. Fuel testing is nowadays a matter of experimental and numerical work. Researches on diesel engine’s fuel involve the use of surrogates, for which the combustion mechanisms are well known and relatively similar to the investigated fuel. Biodiesel, due to its complex molecular configuration, is still the subject of numerous investigations in that area. This study presents the comparison of four biodiesel surrogates, methyl-butanoate, ethyl-butyrate, methyl-decanoate, and methyl-9-decenoate, in a 0D phenomenological combustion model. They were investigated for in-cylinder pressure, thermal efficiency, andNOxemissions. Experiments were performed on a six-cylinder turbocharged DI diesel engine fuelled by methyl ester (MEB) and ethyl ester (EEB) biodiesel from wasted frying oil. Results showed that, among the four surrogates, methyl butanoate presented better results for all the studied parameters. In-cylinder pressure and thermal efficiency were predicted with good accuracy by the four surrogates.NOxemissions were well predicted for methyl butanoate but for the other three gave approximation errors over 50%.