Compared with aviation fuel, biodiesel has a smaller energy density, so the flight range of aircraft using biodiesel as aviation fuel is relatively short. Adding aluminum powder particles can significantly improve the energy density of fuel and then improve the flight range of aircraft, but the combustion characteristics of fuel will change after adding aluminum powder particles to fuel. In this experiment, a tubular furnace was used to simulate the ratio of nitrogen to oxygen in air, and the micro-explosion and combustion characteristics of BD60E40 droplet and BD60E40 droplet 10%AP (8 μm) under 700 and 750 °C were compared and studied by using moving droplet tracking technology. It is found that the greater the steam pressure inside the droplet, the greater the intensity of micro-explosion, and the greater the initial velocity of the secondary droplet after micro-explosion. In addition, it is found that the proportion of aluminum powder in droplets increases gradually during the combustion cycle, and the frequency and intensity of micro-explosion of droplets increase gradually. The instantaneous combustion micro-explosion intensity model and the average combustion intensity model were established. It was found that the average combustion micro-explosion intensity of droplets increased gradually with the increase in temperature through calculation.
To extend the safety service life of aviation TC4 alloy, the composite coatings of TC4 + Ni-MoS2 + WC + xY2O3 (x = 0, 1, 2, 3, 4 wt.%) were prepared on TC4 by coaxial powder feeding laser cladding technology. The results showed that all the coatings had the same generated phases which mainly consisted of TiC, Ti2Ni, Ti2S, matrix β-Ti, and unfused residual WC. Y2O3 formed co-dependent growth relationships with TiC, Ti2S, and Ti2Ni. Meanwhile, TiC-Ti2S, TiC-Ti2Ni, and Ti2S-Ti2Ni coherent composite structure phases were effectively synthesized in all the coatings. With the increase in the Y2O3 content, the exposed area of the matrix increased and other phases refined progressively. When the Y2O3 content in the coatings were 3 and 4 wt.%, the degree of phase refinement in the coatings was consistent and the phases grew along grain boundaries, but microstructure segregated in the 4 wt.% Y2O3 coating. The microhardness of all the coatings was higher than that of TC4 and decreased with the increase in the Y2O3 content. Higher friction coefficients and lower wear rates both appeared in all the coatings than in the substrate, and they presented a trend of decreased first and then increased with the addition of Y2O3, in which the 3 wt.% Y2O3 coating had the lowest friction coefficient and optimal wear resistance. The research found that the Y2O3 could not change the types of phases in the coatings and could serve as a heterogeneous nucleation center for the refinement of the TiC-Ti2S-Ti2Ni coherent structure phase. Meanwhile, except for the matrix phase, Y2O3 could attract other phases to pinning on the grain boundaries of the coatings. The content of Y2O3 was negatively correlated with the hardness and wear resistance of the coating and it had the optimal tribological properties with the moderate amount of Y2O3. The wear mechanism of all coatings was abrasive wear.
Under the continuous tightening of global carbon emission policies, the search for sustainable low-emission energy sources is of great significance to reduce the reliance on the use of fossil fuels and to save energy and reduce emissions. Biodiesel–ethanol–graphene mixed fuel has high combustion efficiency and low emission characteristics, and an in-depth study of its evaporation and microexplosion characteristics during the heating process can help to better understand the characteristics of this fuel. In this paper, the evaporation, microexplosion, sub-droplet distribution and kinematic properties of biodiesel–ethanol–graphene droplets under different temperatures, volumes and mixing ratios were investigated by simulating the air atmosphere using a modified tube furnace experimental platform. It was found that the BD50E50 (1%G) droplet produced a weak microexplosion under 600 °C, and three secondary droplets were formed, with the largest secondary droplet area reaching 5.28 mm2. The BD50E50 (1%G) droplet produced strong microexplosion under 800 °C conditions, and 10 secondary droplets were formed, with the largest secondary droplet area of 3.02 mm2. Different intensities of microexplosion and ejection phenomena produced by the biodiesel–ethanol–graphene droplets during the heating process were found, and it was found that the temperature and droplet volume determine whether the microexplosion of the mixed droplets can occur or not, while the intensity of the microexplosion determines the number of secondary droplets and the speed of movement. Additionally, the velocity and acceleration of secondary droplets produced by ejection were significantly greater than those produced by microexplosion. These studies provide a theoretical basis for the application of this fuel.