Nikola Borovnik

Mr. Nikola Borovnik

orcid

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 August 2025 in Processes
Verified
Journal Article
Open access
PDF file
NBNikola Borovnik
Nikola Borovnik
Sasa MudrinicSasa Mudrinic
Sasa Mudrinic
NFNenad Ferdelji
Nenad Ferdelji
The vacuum drying of cellulose-based insulation is an essential step in the transformer manufacturing process, typically consisting of both heat and vacuum application. The moisture inside cellulose insulation during this process is transferred by various transport mechanisms, some of which are affected by the insulation’s temperature. Moreover, the conditions within the vacuum chamber are generally transient and highly dynamic, depending on the employed process control strategy, and may include various phenomena, such as gas expansion during pump-down and radiative heat transfer. From a modelling perspective, these factors can significantly impact the drying rate by altering the boundary conditions of heat and mass transport equations. To account for such effects, a model that considers the process at both the scale of cellulose insulation and the scale of the vacuum chamber is presented. A simplified drying system with two-point process control is introduced to simulate multiple cases. The results highlight the sensitivity of drying behaviour to both the model parameters and the selected control strategy. A comparison with existing Fickian diffusion models indicates that the proposed model, when properly calibrated, can reliably reproduce drying dynamics and thus provide a powerful tool for optimizing vacuum drying procedures.

18 September 2026 in Systems
Verified
Journal Article
Open access
PDF file
DZDanijel Zadravec
Danijel Zadravec
NFNenad Ferdelji
Nenad Ferdelji
NBNikola Borovnik
Nikola Borovnik
MOMartina Odeljan
Martina Odeljan
Alternative liquefied natural gas (LNG) fuel gas supply system (FGSS) architectures allocate fuel delivery, tank-pressure management, and boil-off gas (BOG) management to different components, creating operating-mode-dependent functional relationships. This study develops a dynamic model of three representative low-pressure architectures based on pressure build-up, pumping, and pumping with compression, and compares them under LNG-only and dual-fuel operating profiles. The LNG tank submodel was validated against published experimental data, with a mean relative pressure deviation below 2.5%. The comparison considers pressure margin, BOG management, energy demand, configuration-specific implementation requirements, and sensitivity to key parameters. Under the dual-fuel profile, pressure margins were 0.50, 0.73, and 3.10 bar for FGSS 1–3, respectively. FGSS 3 required no excess BOG discharge in the base case but had approximately 10.5 times the specific mechanical-energy demand of FGSS 2. Fuel demand most strongly affected voyage endurance, whereas insulation performance strongly influenced tank pressure and BOG management. At the highest insulation thermal conductivity investigated, FGSS 3 reached the maximum allowable working pressure during conventional-fuel operation when compressor-assisted BOG removal was intentionally not used under the adopted strategy. The results show that performance depends on functional allocation, installed capabilities, operating strategy, evolving tank state, and available BOG management pathways, thereby supporting conceptual architecture screening.

25 July 2025 in Preprints.org
Verified
Preprint
Open access
PDF file
NBNikola Borovnik
Nikola Borovnik
Sasa MudrinicSasa Mudrinic
Sasa Mudrinic
NFNenad Ferdelji
Nenad Ferdelji
The vacuum drying of cellulose-based insulation is an essential step in the transformer production process which usually consists of both heat and vacuum application. The moisture inside the cellulose insulation during this process is transferred by various transport mechanisms, some of which could be affected by temperature of the insulation as well. Furthermore, the conditions inside the vacuum chamber are generally transient and highly dynamic depending on the process control strategy and could include various types of phenomena such as gas expansion during the pump down process or heat transfer by radiation. Mathematically speaking, the above-mentioned conditions will have influence on the drying rate by altering the boundary conditions of heat and mass transport equations. In this study, a mathematical model that considers the process at both the scale of the cellulose insulation and the scale of the vacuum chamber is presented. By introducing a simplified drying system with two-point process control, a model test case and drying case were simulated. Model results demonstrated that chamber dynamics significantly affect drying behaviour. The proposed model could thus facilitate the estimation of total energy consumption and process duration, offering a valuable tool for optimization of vacuum drying procedures.