The non-uniform adsorption characteristics of coal strictly restrict the development and utilization of CBM, and the structure of coal is the fundamental reason for its non-uniform adsorption of methane. To investigate the fundamental causes of methane adsorption capacity differences in coal with various meso-structures, small coking coal and lean coal samples were subjected to isothermal adsorption, computed tomography (CT) scanning, scanning electron microscopy (SEM), and mercury intrusion porosimetry (MIP) to obtain the correlation between the meso-structure of coal and its non-uniform adsorption characteristics. The reasons for the differences in methane adsorption capacity between the specimens were summarized from the perspectives of material and structural heterogeneities, meso-morphology and pore size distribution. The following conclusions could be drawn: (1) The coal samples with different heterogeneity degrees exhibit varying methane adsorption capacities. (2) Compared to the specific surface area, the mineral composition exerts a greater influence on the adsorption capacity of the coal samples. (3) The gas adsorption capacities of the coal samples with similar meso-morphology and pore size distribution characteristics are similar, while among the coal samples with similar pore size distributions but different meso-morphologies, the gas adsorption capacities significantly differ.
The creep and stress relaxation behaviors of coal are common in coal mining. The unified constitutive model is suitable to describe and predict both the creep and relaxation evolution characteristics of rocks. The generalized Kelvin model is the core element for traditional and improved component models to reflect both the nonlinear creep and relaxation. In this paper, an improved core damage model, which could both reflect the creep and stress relaxation in relation to the damage evolution, was established based on a comparison of the traditional and improved component models, and the responding constitutive equations (creep and stress relaxation equation) at constant stress/strain were deduced. Then, the core damage model was validated to the uniaxial compressive multistage creep and stress relaxation test results of coal, showing that the model curves had great accordance with the experimental data. Moreover, the model comparisons on accuracy, parameter meaning, and popularization among the core damage model, hardening-damage model, and the fractional derivative model were further discussed. The results showed that the parameters in the core damage model had clear and brief physical significances. The core damage model was also popularized to depict the time-dependent behaviors of other rocks, showing great accuracy.
Fiber reinforcement offers a promising solution to improve the mechanical performance and durability of cement-based foam backfill (CFB), addressing critical issues such as brittleness and poor crack resistance under high-stress conditions. This study investigates the effects of polypropylene and polyacrylonitrile fibers, at varying contents and lengths, on the mechanical and flow properties of CFB. A series of experiments, including slump tests, rheology analysis, uniaxial compressive strength (UCS) tests, pore structure analysis, and scanning electron microscopy (SEM), were conducted to comprehensively evaluate fiber reinforcement mechanisms. The results show that increasing fiber content and length reduced fluidity due to fiber entanglement, while significantly enhancing mechanical properties through anchoring effects and network formation. After 28 days of curing, UCS increased by 208.2% with 2 wt% polypropylene fibers and 215.3% with 1 wt% polyacrylonitrile fibers (both at 6 mm length). Fiber-reinforced CFB demonstrated improved structural integrity and crack resistance, with failure modes transitioning from brittle to ductile. These findings highlight the potential of fiber-reinforced CFB to deliver durable, crack-resistant, and efficient mine backfill solutions, contributing to enhanced safety and sustainability in underground mining operations.
There is a huge reservation of loess in the Shanxi mining area in China, which has great potential for preparing supplementary cementitious materials. Loess was modified via mechanical and thermal activation, and the pozzolanic activity was evaluated using an Inductively Coupled Plasma Optical Emission Spectrometer (ICP-OES). Moreover, the workability of grouting materials prepared using modified loess was assessed. The experimental results revealed that the number of ultrafine particles gradually increased with the grinding time, enhancing the grouting performance. The coordination number of Al decreased upon the breakage of the Al–O–Si bond post-calcination at 400 °C, 550 °C, 700 °C, and 850 °C. Moreover, the breaking of the Si–O covalent bond produced Si-phases, and the pozzolanic activity of loess increased. Furthermore, the modified loess was hydrated with different cement proportions. With increasing grinding time, the overall setting time increased until the longest time of 14.5 h and the fluidity of the slurry decreased until the lowest fluidity of 9.7 cm. However, the fluidity and setting time decreased with increasing calcination temperature. The lowest values were 12.03 cm and 10.05 h. With the increase in pozzolanic activity, more ettringite was produced via hydration, which enhanced the mechanical properties. The maximum strength of the hydrated loess after grinding for 20 min reached 16.5 MPa. The strength of the hydrated loess calcined at 850 °C reached 21 MPa. These experimental findings provide theoretical support for the practical application of loess in grouting.
This study provides an in-depth analysis of the memory deformation characteristics of water-bearing coal-rock assemblages under cyclic loading and its impact on mine safety. With the continuous growth of global coal demand, especially in China, mining activities increasingly involve water-rich environment mines. This trend requires a more comprehensive understanding of the mechanical properties of coal-rock systems and water-insulating coal pillars under water-rock action and their stability. In this study, we conducted cyclic loading and unloading tests under different water saturation rates by constructing specimens of “rock-coal-rock” with different top and bottom lithologies, aiming to analyze the specimens’ deformation memory effect, mechanical damage characteristics, and degradation mechanism. The experimental results show that. With the increase in water saturation rate, the peak strength of the coal-rock assemblage gradually decreased, showing a noticeable deterioration effect. In addition, the specimens under cyclic loading and unloading conditions exhibited a more significant deterioration magnitude than those under uniaxial compression conditions. It was also found that N20 (mudstone-coal-mudstone), S20 (sandstone-coal-sandstone), and SH20 (limestone-coal-limestone) assemblages exhibited different patterns of mechanical strength degradation under water-rock action, with N20 showing the most severe degradation. The damage accumulation of the coal-rock assemblage was monitored by acoustic emission (AE) technology, and an AE damage model based on different water saturation rates was established to quantitatively analyze the damage evolution law of the water-bearing coal-rock assemblage. The findings establish a scientific foundation for predicting coal pillar behavior under cyclic loading, optimizing pillar and support structure design, and highlighting the necessity of drainage, drying, and enhanced reinforcement in long-term water-rich rock systems.
Owing to the heterogeneity, discontinuity and complex material structure, typical coal exhibits intricate deformation characteristics during long-term creep processes. This study investigates obvious three-stage asynchronous strain evolution characteristics between axial and radial strain of lean coal specimens during uniaxial compression creep tests with staged loading. The radial and axial creep strains are non-synchronous; specifically, the radial creep strain noticeably lags the axial creep strain. Under low-stress levels, both axial and radial strains exhibit instantaneous elastic–plastic behavior with no creep behaviors. At intermediate stress levels, creep strain is not observed before the creep-initiation stress threshold. Axial time-dependent creep strain appears earlier than the radial creep. Under high-stress conditions, although both the axial and radial strains both show pronounced time-dependent creep characteristics, behaving transient and steady creep, the asynchronous strain coefficient and the creep rates of the axial and radial creep differ greatly under identical stress levels. An improved fractional-order creep constitutive model is established and the model parameters were identified. Despite the observed asynchrony, both the axial and radial strains exhibit similar patterns and can well be described by the same creep model, but with different parameters, under identical stress levels. The model parameters of axial and radial strains are independent. These findings can assist predictions of catastrophic failures in geotechnical engineering, contributing to the prevention of geological disasters such as landslides.