Among different organic fillers, the chemical composition of Syzygium aromaticum, commonly known as cloves, has great potential as a sustainable reinforcement for polymeric materials. In the study, grounded cloves were used as cellulosic filler for a novel polyurethane (PU) composite foams. Soybean oil-based PU composite foams were successfully reinforced with different concentrations (1, 2, and 5 wt%) of clove filler. PU foams were examined by rheological behavior, processing parameters, cellular structure (scanning electron microscopy analysis), mechanical properties (compression test, impact test, three-point bending test), thermal properties (thermogravimetric analysis), viscoelastic behavior (dynamic mechanical analysis) as well as selected application properties (apparent density, dimensional stability, surface hydrophobicity, water absorption, color characteristic). In order to undertake the disc diffusion method, all PU composites were tested against selected bacteria (Escherichia coli and Staphylococcus aureus). Based on the results, it can be concluded that the addition of 1 and 2 wt% of clove filler leads to PU composite foams with improved compression strength (improvement by ≈18% for sample PU-1), greater flexural strength (increase of ≈11%), and improved impact strength (increase of ≈8%). Moreover, it has been proved that clove filler may be used as a natural anti-aging compound for polymeric materials. Based on the antibacterial results, it has been shown that the addition of clove filler significantly improved the antibacterial properties of PU foams and is suitable for the manufacturing of antimicrobial PU composite foams. Due to these positive and beneficial effects, it can be stated that the use of cloves as a natural filler in PU composite foams can promote a new application path in converting agricultural waste into useful resources for creating a new class of green materials.

Rigid polyurethane foams (RPUFs) were successfully modified with different weight ratios (0.5 wt%, 1.5 wt% and 5 wt%) of APIB-POSS and AEAPIB-POSS. The resulting foams were evaluated by their processing parameters, morphology (Scanning Electron Microscopy analysis, SEM), mechanical properties (compressive test, three-point bending test and impact strength), viscoelastic behavior (Dynamic Mechanical Analysis, DMA), thermal properties (Thermogravimetric Analysis, TGA, and thermal conductivity) and application properties (contact angle, water absorption and dimensional analysis). The results showed that the morphology of modified foams is significantly affected by the type of the filler and filler content, which resulted in inhomogeneous, irregular, large cell shapes and further affected the physical and mechanical properties of resulting materials. RPUFs modified with APIB-POSS represent better mechanical and thermal properties compared to the RPUFs modified with AEAPIB-POSS. The results showed that the best results were obtained for RPUFs modified with 0.5 wt% of APIB-POSS. For example, in comparison with unfilled foam, compositions modified with 0.5 wt% of APIB-POSS provide greater compression strength, better flexural strength and lower water absorption.

This study aimed to examine rigid polyurethane (PUR) foam properties that were synthesized from walnut shells (WS)-based polyol. The Fourier Transform Infrared Spectroscopy (FTIR) results revealed that the liquefaction of walnut shells was successfully performed. The three types of polyurethane (PUR) foams were synthesized by replacement of 10, 20, and 30 wt% of a petrochemical polyol with WS-based polyol. The impact of WS-based polyol on the cellular morphology, mechanical, thermal, and insulating characteristics of PUR foams was examined. The produced PUR foams had apparent densities from 37 to 39 kg m⁻³, depending on the weight ratio of WS-based polyol. PUR foams that were obtained from WS-based polyol exhibited improved mechanical characteristics when compared with PUR foams that were derived from the petrochemical polyol. PUR foams produced from WS-based polyol showed compressive strength from 255 to 310 kPa, flexural strength from 420 to 458 kPa, and impact strength from 340 to 368 kPa. The foams that were produced from WS-based polyol exhibited less uniform cell structure than foams derived from the petrochemical polyol. The thermal conductivity of the PUR foams ranged between 0.026 and 0.032 W m⁻¹K⁻¹, depending on the concentration of WS-based polyol. The addition of WS-based polyol had no significant influence on the thermal degradation characteristics of PUR foams. The maximum temperature of thermal decomposition was observed for PUR foams with the highest loading of WS-based polyol.

Currently, there is great demand to implement circular economy principles and motivate producers of building materials to integrate into a closed loop supply chain system and improve sustainability of their end-product. Therefore, it is of great interest to replace conventional raw materials with inorganic or organic waste-based and filler-type additives to promote sustainability and the close loop chain. This article investigates the possibility of bottom waste incineration ash (WA) particles to be used as a flame retardant replacement to increase fire safety and thermal stability under higher temperatures. From 10 wt.% to 50 wt.% WA particles do not significantly deteriorate performance characteristics, such as compressive strength, thermal conductivity, and water absorption after 28 days of immersion, and at 32 °C WA particles improve the thermal stability of resultant PU foams. Furthermore, 50 wt.% WA particles reduce average heat release by 69% and CO₂ and CO yields during fire by 76% and 77%, respectively. Unfortunately, WA particles do not act as a smoke suppressant and do not reduce smoke release rate.

Currently, polyurethane foam producers come across the several problems when petroleum-based polyols are replaced with low functionality biomass, or waste-based, polyols. In addition, the dilemma is intensified with regulations that require full or partial replacement of blowing agents that can cause high ozone depletion with alternatives like water, which causes the formation of CO₂. Therefore, these gases diffuse out of the foam so quickly that the polymeric cell walls cannot withstand the pressure, consequently causing huge dimensional changes at ambient temperature and humidity. Even though the theoretical stoichiometric balance is correct, the reality shows that it is not enough. Therefore, polyethylene terephthalate waste-based polyol was chosen as a low functionality polyol which was modified with high functionality sucrose-based polyol in order to obtain dimensionally stable polyurethane foams in the density range of 30–40 kg/m³. These more stable foams are characterized by linear changes no higher than 0.5%, short-term water absorption by partial immersion no higher than 0.35 kg/m², and water vapor resistance factors up to 50. In order to obtain thermally efficient polyurethane foams, conventional blowing agents and water systems were implemented, thus, assuring thermal conductivity values in the range of 0.0198–0.0204 W/(m·K) and obtaining products which conform to all the requirements for performance of sprayed and factory-made polyurethane foam standards EN 14315-1 and EN 13165.

Currently, the recycling potential of wood waste (WW) is still limited, and in a resource efficiency approach, recycling WW in insulation materials, such as polyurethane (PUR), appears as an appropriate solution. It is known that the quality of WW is the main aspect which influences the stability of the final products. Therefore, the current study analyses different WW-based fillers as possible modifiers for polyurethane biocomposite foams for the application as loose-fill materials in building envelopes. During the study of WW-based fillers, it was determined that the most promising filler is wood scobs (WS) with a thermal conductivity of 0.0496 W/m·K, short-term water absorption by partial immersion—12.5 kg/m², water vapour resistance—0.34 m²·h·Pa/mg and water vapour diffusion resistance factor—2.4. In order to evaluate the WS performance as a filler in PUR biocomposite foams, different ratios of PUR binder and WS filler (PURb/WS) were selected. It was found that a 0.40 PURb/WS ratio is insufficient for the appropriate wetting of WS filler while a 0.70 PURb/WS ratio produced PUR biocomposite foams with the most suitable performance: thermal conductivity reduced from 0.0523 to 0.0476 W/m·K, water absorption—from 5.6 to 1.3 kg/m², while the compressive strength increased from 142 to 272 kPa and the tensile strength increased from 44 to 272 kPa.