Lignocellulosic biomasses have a tremendous potential to cover the future demand of bio-based chemicals and materials, breaking down our historical dependence on petroleum resources. The development of green chemical technologies, together with the appropriate eco-politics, can make a decisive contribution to a cheap and effective conversion of lignocellulosic feedstocks into sustainable and renewable chemical building blocks. In this regard, the use of an indirect H-source for reducing the oxygen content in lignocellulosic biomasses and in their derived platform molecules is receiving increasing attention. In this contribution we highlight recent advances in the transfer hydrogenolysis of cellulose, hemicellulose, lignin, and of their derived model molecules promoted by heterogeneous catalysts for the sustainable production of biofuels and biochemicals.

Carbon (Vulcan XC-72)-supported bimetallic Pd–Ir catalysts with different Pd/Ir proportions (5–50 mol% Ir, 2 wt% Pd) were prepared by “water-in-oil” microemulsion method (w/o) using solutions of low (0.02 M, L series) and high concentration (0.2 M, H series) of the metals precursors (PdCl₂ and IrCl₃). The bimetallic particles were examined in terms of nanoscale phase properties (extent of Pd–Ir alloying, phase separation), surface composition (Pd and Ir fractions) and electrocatalytic performance for the formic acid oxidation reaction. Structural characterization was performed using XRD, SEM and HRTEM techniques. Electrochemical characterization allowed estimating the PdH formation ability and the surface composition of Pd–Ir particles what was confirmed by XPS data. The Pd–Ir nanoparticles of similar average size (ca. 4 nm), close to that of Ir (3.8 nm) and below that of Pd (6.2 nm) were formed regardless of the Pd/Ir proportion and the concentration of the metals precursors in the w/o. In contrast to the largely alloyed PdIr nanoparticles with the Pd-rich surface formed at low concentration of the metals precursors (0.02 M), the particles of almost closed surface and bulk Pd/Ir ratios composed mostly of randomly distributed single-phase domains were formed at high concentration (0.2 M). At the lowest bulk Ir content, 5 mol%, the particles have Ir-rich surface regardless of the preparation method. The catalytic studies involving formic acid electrooxidation reaction showed the activity enhancement for the L series catalysts with respect to monometallic Pd/C (twofold TOF increase) and H series counterparts. The Pd₈₅Ir₁₅/C catalyst of the Pd–Ir alloyed and the surface composition expressed by the Pd/Ir atomic ratio near to 6 displayed the highest activity which was 2.9-times higher relative to that of Pd. Graphic

Supported Pd/Ir bimetallic catalysts were synthesized by the “water-in-oil” microemulsion method at different precursor concentrations and characterized by XRD, XPS, SEM, TEM, and cyclic voltammetry. Depending on the preparation conditions, formation of bimetallic catalysts with different metal segregation and surface composition can be easily obtained, thus tuning the bimetallic structure of catalysts as well as their relative catalytic properties. Bimetallic Pd/Ir systems were efficiently tested in the hydrogenation of cinnamaldehyde showing a better performance than analogous monometallic catalysts.

We present an efficient strategy for synthesising the PdAu catalysts with a homogeneous PdAu alloy phase for environmentally important hydrodechlorination of tetrachloromethane in the gas phase. The synthesis of carbon-supported catalysts involved two major steps: (i) incorporation of palladium and gold nanoparticles into carbon support and (ii) activation of the catalysts. The critical part of this work was to find the optimal conditions for both steps. Thus, the incorporation of the nanoparticles was carried out in two ways, by impregnation and direct redox reaction method using acetone solutions of metal precursor salts. The activation was performed either by a conventional thermal reduction in hydrogen or flash irradiation in a microwave oven. The homogeneity and structure of the PdAu alloy were found to depend on the catalyst activation method critically. In all cases, we observed better homogeneity for catalysts that were subject to microwave irradiation. Moreover, the flash microwave irradiation of prepared catalysts provided catalysts of better stability and selectivity towards the desired products (hydrocarbons) in the hydrodechlorination of tetrachloromethane as compared to the catalyst obtained by conventional thermal activation in hydrogen.