To date, two-phase flow boiling has been extensively investigated for various working fluids and geometries, mainly under operating pressures and mass fluxes in the range of medium to high. However, very limited studies have been conducted, focusing on low-pressure low-flow (LPLF) conditions. Given insufficient experimental data available in the literature, most of the existing empirical correlations fail to properly predict boiling heat transfer coefficients (BHTCs) in LPLF conditions, highlighting the need for further experimental investigations. The present study experimentally investigates the heat transfer performance of single-phase and two-phase flow boiling of distilled water in a horizontal conventional tube at constant wall heat flux under LPLF conditions where the operating pressure is set to be subatmospheric and the mass flux ranges below 20 kg/m2-s. For the saturated flow boiling, the effects of mass flux and local vapor quality on the local BHTCs and Nusselt were evaluated, revealing that local BHTCs reach a peak at a certain range of vapor qualities between 55% and 75%, while increasing with the mass flux. It was also found that the impact of mass flux is stronger than that of vapor quality on the local BHTCs. The experimental results in the present study were then compared with several well-known empirical BHTC correlations in the literature to identify those with least deviations under the LPLF conditions. In contrast to single-phase flow, heat loss estimation and vapor quality measurement are known as one of the main error sources in characterizing heat transfer coefficients for two-phase flow boiling. Accordingly, the present study employs two approaches, in parallel, to reliably estimate heat losses, calibrate heat supplies, and measure local vapor qualities under the operating conditions investigated.
Эффекты течения однофазной наножидкости в мини- и микроканалах исследовались как экспериментально, так и численно в литературе в течение последнего десятилетия. Почти все исследования показывают аналогичную тенденцию, согласно которой взаимодействие однофазных наножидкостей с мини- и микроканалами обеспечивает значительное улучшение тепловых характеристик. Однако в литературе имеется ограниченное количество публикаций с экспериментальными исследованиями характеристик теплообмена наножидкостей при кипении двухфазного потока в мини- и микроканалах. Кроме того, в имеющихся экспериментальных исследованиях отмечаются некоторые заметно противоречивые тенденции, особенно в отношении коэффициента теплообмена при кипении. В настоящем обзоре основная причина противоречий, отраженных в литературе по экспериментальным измерениям коэффициента теплообмена при кипении, прослеживается в различных закономерностях осаждения наночастиц разного размера на поверхности кипения и последующих изменениях морфологии и характера кипения. Определены ключевые параметры наножидкостей при кипении потока в мини- и микроканалах, и всесторонне рассмотрено влияние этих параметров на характеристики теплообмена при кипении. Также выявлены и проанализированы соответствия и расхождения, о которых сообщается в литературе. Сделан ряд предложений для будущих экспериментальных исследований кипения наножидкостей, чтобы свести к минимуму противоречивые сообщения.
Phase-change materials (PCMs) are capable of storing or releasing a substantial amount of thermal energy within a small volume through the latent heat of fusion during phase transitions of melting and solidification, i.e., from solid to liquid or vice versa, in a near isothermal process. However, commonly used organic PCMs, such as paraffin wax, exhibit very low thermal conductivity, contributing to an adverse increase in overall thermal resistance and, thus, a slow thermal response. This limitation often becomes a bottleneck for the system from a thermal performance standpoint. To mitigate this issue, the present work explores the fabrication of heat sinks incorporating nano-structured graphitic foams, including carbon foam (CF) and expanded graphite (EG), as well as micro-structured metal foams such as open-cell copper foam (OCCF), all impregnated with a paraffin-based PCM with a melting temperature near 37 °C. This study focuses on applying passive thermal management strategies to design efficient heat sinks capable of maintaining the temperatures of battery modules and electronic circuits within an acceptable thermal safety threshold for small satellites and spacecrafts, exemplified by the OPTIMUS and Pumpkin battery modules designed for CubeSats with a nominal cross-sectional area of almost 4″ × 4″. Temperature responses and average overall thermal resistances for fabricated heat sinks are accordingly assessed and compared in a vacuum chamber to simulate space conditions. Furthermore, the impact of operating pressure on the thermal performances of various heat sinks will be investigated by executing the same tests in both atmospheric and vacuum conditions. The findings demonstrate a superior thermal performance of composite heat sinks integrating carbon foam and copper foam into the paraffin PCM compared to the baseline PCM heat sink under both vacuum and atmospheric operating pressure conditions.
Possessing high latent heat of fusion and high thermal energy storage density, phase-change materials (PCMs) offer an energy-efficient and sustainable approach to passive thermal management. However, conventional organic PCMs such as paraffin wax exhibit inherently low thermal conductivity, resulting in high thermal resistance and slow thermal response. In contrast, eutectic alloy PCMs, particularly low-melting-point alloys (LMPAs), exhibit thermal conductivities nearly two orders of magnitude higher than those of paraffins, making them promising candidates for passive thermal management and thermal energy storage in spacecraft, where maintaining thermal stability and minimizing temperature fluctuations are critical due to substantial environmental variations during orbital operation. To address the thermal transport limitations of PCMs, this study experimentally investigates PCM-based heat sinks incorporating micro-structured metal foams and nano-structured graphitic carbon foams infiltrated with either a bismuth-based LMPA or paraffin PCM, both with a melting temperature of approximately 47 °C. The thermal performance of these heat sinks is evaluated under vacuum conditions representative of space environments by comparing their temperature responses and average thermal resistances. Foam-enhanced paraffin configurations incorporating copper and carbon foams are also examined for comparison with the LMPA-based systems. Baseline heat sinks containing pure paraffin and LMPA without conductivity enhancers are tested under both atmospheric and vacuum conditions, with the experimental baseline results validated against numerical simulations. The results demonstrate that foam-enhanced composite heat sinks improve average thermal resistance by nearly 22% relative to their corresponding baseline configurations. Moreover, foam-enhanced LMPA-based heat sinks achieve reductions of more than 50% in average thermal resistance compared with the base paraffin configuration, underscoring the potential of LMPA–foam composites for passive thermal management of battery modules and electronic components in spacecraft. Nevertheless, the mass of the base LMPA configuration is approximately 10 times that of the base paraffin configuration for an equivalent PCM volume, highlighting the trade-off between enhanced thermal performance and mass constraints in spacecraft applications.