Mohammed Basheer Alameen

Dr. Mohammed Basheer Alameen

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 January 2024 in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
Verified
Journal Article
Open access
PDF file
MAMohammed Basheer Alameen
Mohammed Basheer Alameen
KEKhaled Elraies
Khaled Elraies
AAAbdullah Almansour
Abdullah Almansour
MEMysara Eissa
Mysara Eissa
HHHaithm Hagar
Haithm Hagar
The issue of sand production in reservoirs has been recognized as a critical problem in oil and gas fields for several years due to its numerous negative impacts on oil and gas production. Sand production from wells can damage both surface and subsurface equipment, reduce well productivity, and negatively impact the oil production economy. Oil production challenges arise when sand production increases as the water cut increases. Several factors have been associated with this phenomenon, with the most critical factor being silica dissolution - a chemical reaction between quartz and water that decreases formation strength. This study explores the dissolution of silica on pure quartz and the effects of added electrolyte (NaCl, CaCl2, MgCl2, and KCl) concentration, temperature, and pH on the dissolution process. The concentration of silica dissolved in solution was measured using UV-Vis spectrophotometry to determine the dissolution of silica on quartz. The results outcome indicate that the rate of silica dissolution is significantly influenced by variations in temperature and alterations in pH levels. The salinity conditions exhibit minimal alterations in comparison to distilled water. The highest concentration of silica dissolved in a solution has been seen at pH levels of 12 and 3, with concentrations of 118 mg/l and 68 mg/l, respectively. In terms of temperature, it was observed that there was an increase in the dissolution of silica from 30°C to 90°C, ranging from around 170% to 600%. Regarding salinity, it can be shown that NaCl and KCl exhibit the most significant impact on silica dissolution when compared to other brine solutions, with concentrations of 45 and 49 mg/l, respectively. The study claims that the formation strength may be influenced by water quality through the processes aimed at stimulating or lowering silica dissolution. Therefore, the optimal water quality design for water injection is paramount in mitigating sand production challenges.

17 June 2025 in Results in Engineering
Verified
Journal Article
Open access
MAMohammed Basheer Alameen
Mohammed Basheer Alameen
KEKhaled A. Elraies
Khaled A. Elraies
AAAbdullah Almansour
Abdullah Almansour
MMMysara Mohyaldinn
Mysara Mohyaldinn
OAOkorie E. Agwu
Okorie E. Agwu

11 October 2025 in Chemengineering
Verified
Journal Article
Open access
PDF file
SMSulafa Mohammed
Sulafa Mohammed
KEKhaled Elraies
Khaled Elraies
MAMohammed Basheer Alameen
Mohammed Basheer Alameen
Mohammed AwadMohammed Awad
Mohammed Awad
The flaring of associated gas in oil and gas operations contributes significantly to greenhouse gas emissions and represents a loss of valuable hydrocarbon resources. While amine absorption is widely applied for acid gas removal, the use of supercritical carbon dioxide (sc-CO2) for flare gas treatment remains largely unexplored, despite its proven selectivity for hydrocarbons in other industries such as natural product extraction and polymer processing. Conventional flare gas treatment methods face trade-offs: amine absorption achieves high acid gas removal efficiency but offers limited selectivity for heavier hydrocarbons, whereas sc-CO2 extraction enables efficient recovery of higher hydrocarbons but does not fully remove acid gases. This study addresses these gaps by evaluating three two-stage flare gas treatment configurations—dual-stage amine absorption, dual-stage sc-CO2 absorption, and a hybrid of sc-CO2 followed by amine absorption—using Aspen HYSYS V12.1 simulations, with recycling processes considered in each case. The dual-stage sc-CO2 process achieved nearly complete hydrocarbon recovery (100%) and complete H2S removal, but CO2 remained at elevated concentrations in the treated gas. The dual-stage amine process completely removed CO2 and H2S, though with higher energy demand for solvent regeneration. The hybrid configuration combined the advantages of both approaches, achieving complete H2S removal, 100% hexane recovery, 95.02% methane recovery, and a drastic reduction in CO2 concentration (to 0.0012 mole fraction). These results demonstrate that integrating sc-CO2 with amine absorption resolves the trade-off between hydrocarbon selectivity and acid gas removal, establishing a technically viable pathway for flare gas utilization with potential application in gas-to-liquids (GTL) and carbon management strategies

18 July 2023 in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
Verified
Journal Article
Open access
PDF file
MEMuhammad Ridho Efras
Muhammad Ridho Efras
IDIskandar B Dzulkarnain
Iskandar B Dzulkarnain
MMMohammad Galang Merdeka
Mohammad Galang Merdeka
FRFarah Rosmaniza Redzuan
Farah Rosmaniza Redzuan
NRNovia Rita
Novia Rita
MAMohammed Basheer Alameen
Mohammed Basheer Alameen
Steamflood is one of the best thermal enhanced oil recovery methods to improve heavy oil production. This project focuses on the benchmarks of steamflood performance in two types of sand: homogenous and heterogeneous formations in the XYZ field. The co-kriging technique was implemented to generate the porosity and net to gross distribution. Afterward, twelve designs of experiments were run to obtain the oil production information and analyze the affecting factors of steamflood performance on each sand. The findings showed that clean sand provided higher oil production compared to the fining sand. Additionally, the well spacing had a higher contribution compared to the steam quality in applying steamflood injection. This study could serve as a guideline for engineers for planning the well spacing and steam quality utilization in steamflood injection in these two types of sand formation that contain heavy oil reserves.