Abdullah Almansour

Dr. Abdullah Almansour

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 March 2017 in Journal of Petroleum Exploration and Production Technology
Verified
Journal Article
Open access
PDF file
AAAbdullah Almansour
Abdullah Almansour
AAAbdulrahman A. AlQuraishi
Abdulrahman A. AlQuraishi
SASaud N. AlHussinan
Saud N. AlHussinan
HAHamdan Q. AlYami
Hamdan Q. AlYami
Oil recovery from heavy oil resources has always been a challenging task. This work is aimed at investigating the recovery efficiency of polymer-augmented low salinity waterflooding in heavy oil reservoirs. The main recovery mechanism behind low salinity waterflooding is wettability alteration to more water-wet state. On the other hand, polymer flooding is performed to control fluids mobility and hence improve displacement efficiency. Combining both recovery methods is expected to add to recovery efficiency obtained by individual methods, and the aim of this work is to explore this experimentally. In this study, several laboratory experiments were conducted using Berea and Bentheimer sandstone cores starting with base runs of continuous secondary seawater and tertiary twice and 10 times diluted seawaterflooding (low salinity). Significant incremental oil recovery was obtained when flooded with low salinity water, and 10 times diluted seawater was determined to be used as low salinity water. Contact angle and Zeta potential measurements indicate wettability alteration due to clay detachment as the main recovery mechanism. Synergy of water secondary flooding and polymer tertiary flooding at different water salinity levels proved the efficiency of hybrid low salinity polymer flooding process in Berea sandstone. Low water salinity during secondary injection mode played a major role on ultimate recovery with less contribution to tertiary polymer slug injection. High salinity waterflooding provided lower secondary recovery leaving more residual oil for polymer slug to act on at that cycle. Smaller polymer slug of 0.1 pore volume was found to be sufficient in tertiary flooding with low salinity water but with slightly slower recovery rate. Bentheimer sandstones known for its low clay content were subjected to polymer-augmented waterflooding at high and low salinity levels. Close secondary and tertiary recoveries were obtained for the two salinity levels with slower recovery rate for low salinity run. Minute clay content and water-wet characteristic as determined by contact angle measurements may explain the lack of water salinity effect on recovery. The lack of salinity role and the two shock fronts with connate water bank in between known to exist during low salinity flooding may explain the slower recovery rate encountered. Comparison of both sandstones indicates that less ultimate recovery from Berea rocks, and this can be attributed to their initial intermediate wet state in contrast to the water-wet Bentheimer sandstone rocks.

22 April 2022 in Energies
Verified
Journal Article
Open access
PDF file
AHAnas M Hassan
Anas M Hassan
Mohammed Abdalla Ayoub MohammedMohammed Abdalla Ayoub Mohammed
Mohammed Abdalla Ayoub Mohammed
MEMysara Eissa
Mysara Eissa
Emad W. Al ShalabiEmad W. Al Shalabi
Emad W. Al Shalabi
AAAbdullah Almansour
Abdullah Almansour
AAAbdulrahman Al-Quraishi
Abdulrahman Al-Quraishi
This contribution introduces a new hybrid enhanced oil recovery (EOR) method which combines smart water-assisted foam (SWAF) flooding, known as the SWAF process. The concept of applying SWAF flooding in carbonate reservoirs is a novel approach previously unexplored in the literature. The synergy effect of the SWAF technique has the potential to mitigate a number of limitations related to individual (i.e., conventional water injection and foam flooding) methods encountered in carbonates. In general, carbonate rocks are characterized by a mixed-wet to oil-wet wettability state, which contributes to poor oil recovery. Hence, the smart water solution has been designed to produce a dual-improvement effect of altering carbonate rock wettability towards more water-wet, which preconditions the reservoir and augments the stability of the foam lamellae, which has for some conditions more favorable relative permeability behavior. Then the smart water solution is combined with surfactant (surfactant aqueous solution or SAS) and gas injection produces a synergy effect, which leads to more wettability alteration, and interfacial tension (IFT) reduction, and thus improves the oil recovery. Accordingly, to determine the optimal conditions of smart water solution with an optimal SAS, we conducted a series of experimental laboratory studies. The experimental design is divided into three main steps. At first, the screening process is required so that the candidates can be narrowed down for our designed smart water using the contact angle tests that employ calcite plate (i.e., Indiana limestone or ILS) as the first filter. Following this, the optimum smart water solutions candidates are blended with different types of cationic and anionic surfactants to create optimum SAS formulations. Subsequently, a second screening process is performed with the aim to narrow down the SAS candidates with varying types of gases (i.e., carbon dioxide, CO2 and nitrogen, N2) via the aqueous stability test (AST), foamability test (FT), and foam stability test (FST). We employed the state-of-the-art R5 parameter tests for rapid and accurate results in place of the conventional foam half-life method. The most effective combination of SAS and gas candidates are endorsed for the core-flooding experiments. In this work, two types of crude oils (Type A and B) with different total acid and base numbers (TAN and TBN). Results showed that the greatest wettability changes occurred for SW (MgCl2) solution at 3500 (ppm) for both crude oil types. This demonstrates the efficacy of our designed SW in the wettability alteration of carbonates, which is also supported by the zeta-potential measurements. The concentrations of both SW (MgCl2) and CTAB-based surfactants considerably affect the stability of the SAS (i.e., up to 90% foam stability). However when in the presence of crude oil, for the same SAS solution, the foam stability is reduced from 90% to 80%, which indicates the negative effect of crude oil on foam stability. Moreover, the core floods results showed that the MgCl2-foam injection mixture (MgCl2 + CTAB + AOS + N2) provided the highest residual oil recovery factor of SWAF process of 92% cumulative recovery of original oil in core (OIIC). This showcases the effectiveness of our proposed SWAF technique in oil recovery from carbonate reservoirs. Additionally, changing the large slug of 5 PVs to a small slug of 2 PVs of smart water solution was more effective in producing higher OIIC recovery and in reducing the fluid circulation costs (i.e., thereby, lowering CO2 footprint), making the SWAF process environmentally benign. Thus, it is expected that under optimum conditions (SW solution and SAS), the novel SWAF process can be a potentially successful hybrid EOR method for carbonate reservoirs, having both economic and environmental benefits.

8 January 2024 in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
Verified
Journal Article
Open access
PDF file
MAMohammed Basheer Alameen
Mohammed Basheer Alameen
KEKhaled Elraies
Khaled Elraies
AAAbdullah Almansour
Abdullah Almansour
MEMysara Eissa
Mysara Eissa
HHHaithm Hagar
Haithm Hagar
The issue of sand production in reservoirs has been recognized as a critical problem in oil and gas fields for several years due to its numerous negative impacts on oil and gas production. Sand production from wells can damage both surface and subsurface equipment, reduce well productivity, and negatively impact the oil production economy. Oil production challenges arise when sand production increases as the water cut increases. Several factors have been associated with this phenomenon, with the most critical factor being silica dissolution - a chemical reaction between quartz and water that decreases formation strength. This study explores the dissolution of silica on pure quartz and the effects of added electrolyte (NaCl, CaCl2, MgCl2, and KCl) concentration, temperature, and pH on the dissolution process. The concentration of silica dissolved in solution was measured using UV-Vis spectrophotometry to determine the dissolution of silica on quartz. The results outcome indicate that the rate of silica dissolution is significantly influenced by variations in temperature and alterations in pH levels. The salinity conditions exhibit minimal alterations in comparison to distilled water. The highest concentration of silica dissolved in a solution has been seen at pH levels of 12 and 3, with concentrations of 118 mg/l and 68 mg/l, respectively. In terms of temperature, it was observed that there was an increase in the dissolution of silica from 30°C to 90°C, ranging from around 170% to 600%. Regarding salinity, it can be shown that NaCl and KCl exhibit the most significant impact on silica dissolution when compared to other brine solutions, with concentrations of 45 and 49 mg/l, respectively. The study claims that the formation strength may be influenced by water quality through the processes aimed at stimulating or lowering silica dissolution. Therefore, the optimal water quality design for water injection is paramount in mitigating sand production challenges.

10 October 2024 in Energies
Verified
Journal Article
Open access
PDF file
AAAbdulrahman A. AlQuraishi
Abdulrahman A. AlQuraishi
AAAbdullah Almansour
Abdullah Almansour
KAKhalid A. AlAwfi
Khalid A. AlAwfi
FAFaisal Alonaizi
Faisal Alonaizi
HAHamdan Q. AlYami
Hamdan Q. AlYami
AAAli M. AlGhamdi Ali
Ali M. AlGhamdi Ali
Organic-rich hot Qusaiba shale is the primary source rock of most of the Paleozoic hydrocarbon reservoirs of eastern and central Arabia. Representative near-surface Qusaiba shale samples were collected and characterized from one of its outcrop sections at the Tayma quadrangle in northwest Saudi Arabia. The petrophysical and geochemical characterization indicated porosity and permeability of 8.2% and 2.05 nD, respectively, with good total organic carbon (TOC) of 2.2 mg/g and mature kerogen of gas-prone type III. The tight characteristics of the formation can lead to high capillary pressure and extensive post-fracking water retention, leading to flow blockage and a reduction in gas productivity. Three different surfactants and one ionic liquid, namely, Triton X-100, Triton X-405 and Zonyle FSO surfactants and Ammoeng 102 ionic liquid, were tested as additives to fracking fluid to investigate their effectiveness in optimizing its performance. The chemical solutions exhibited no sign of instability when exposed to solution salinity and temperatures up to 70 °C. The investigated chemicals’ performance was examined by measuring methane/chemical solutions’ surface tension and their ability to alter shale’s wettability. The results indicate that Zonyl FSO is the most effective chemical, as it is able to significantly reduce surface tension and, hence, capillary pressure by 66% when added at critical micelle concentration (CMC). Using Zonyl FSO surfactant at a maximum tested concentration of 0.2% induced a relatively smaller capillary pressure drop (54%) due to the drastic drop in the contact angle rendering shale very strongly water-wet. Such a drop in capillary pressure can lower the fracking fluid invasion depth and therefore ease the liquid blockage removal during the flowback stage, enhancing gas recovery during the extended production stage. Triton X-100 at CMC was the second most effective surfactant and was able to induce a quite significant 47% drop in capillary pressure when added at the maximum tested concentration of 0.05%. This was sufficient to remove any liquid blockage but was less likely to alter the wettability of the shale. Based on the findings obtained, it is suggested to reduce the blockage tendency during the fracking process and elevate any existing blockage during the flowback stage by using Zonyl FSO at CMC where IFT is at its minimum with a higher contact angle.

12 November 2024 in Preprints.org
Verified
Preprint
Open access
PDF file
FAFaris Almansour
Faris Almansour
GAGeamel H Alyami
Geamel H Alyami
AAAbdullah Almansour
Abdullah Almansour
This paper aims to nurture the need to find an ecological solution to the use of conventional plastic materials, which has risen to be a threat to the environment and economic activities due to increased carbon emissions and the depletion of resources. It looks at the possibility of using sustainable polymers (SPs), which offer many benefits over traditional polymers in terms of carbon footprint and resource usage. The study then systematically analyzes how the technological developments in renewable energy (RE) deployment and circular economy have informed integration with SP production, including cost recoveries and potential for generating employment in sustainable sectors. However, there is also information on the impediments that prevent the broader application of nanomaterials: the high cost of fabrication, the unsuitable characteristics of most materials, and supply chain issues. The paper ends with a proposal for future research works on polymer degradation, the manufacturing cost of SPs, and the incorporation of carbon capture to make the application of SPs favorable economically and ecologically in different industries.