With the advantages of a high power-to-weight ratio and oil-free bearings, a magnetically suspension centrifugal compressor (MSCC) equipped with active magnetic bearings operates more efficiently than the traditional mechanical compressors over a wide speed range by precisely controlling a high-speed permanent-magnet synchronous motor (PMSM). However, owing to the harsh working environment, the motor parameters, including the resistor, inductance, and flux linkage, vary significantly. This degrades the rotor position observer performance, which is crucial for controlling a high-speed PMSM. Hence, this article proposes an improved sensorless control method combined with novel motor parameter identification. First, an improved position sliding mode observer using a novel supertwisting algorithm is designed to achieve higher precision and better transient performance. Second, the influence of parameter mismatch is analyzed. To overcome the problems of rank deficiency and system matrix uncertainties, a novel identification strategy based on recursive total least-squares excitatory and inhibitory learning is developed to identify inductance and resistance in two-time scales. Meanwhile, the back electromotive force in static coordinates is employed to estimate the flux linkage. Third, the results are adopted to update the control parameters immediately. Finally, the proposed method is tested on an MSCC prototype experimental platform, and the results verify its validity and feasibility.
22 August 2023 in IEEE Transactions on Power Electronics
As considering both copper loss and iron loss, the loss minimization control (LMC) method could help permanent magnet synchronous motors (PMSMs) get higher efficiency compared with the traditional maximum torque per ampere control method. Unfortunately, it suffers from approximate models and the electromagnetic torque, which is hard to get precisely. To overcome these shortcomings and further improve efficiency, this article proposes an improved LMC method based on bivariate extreme value theory for PMSMs. First of all, based on the equivalent model of PMSM considering both copper loss and iron loss, the electrical loss of the PMSM is transformed into a function of the d-q -axis currents. Then, according to the bivariate extreme value theory, the optimal d-q -axis currents without the torque constraint are obtained. On this basis, the optimal d- axis active current model is derived, while the q -axis active current is obtained by the speed controller. After that a current regulator with the feedforward decoupling control of iron loss currents is designed to realize the LMC strategy with implicit torque constraint. At last, implementing comparative experiments with i d = 0 control and traditional LMC method, the improved LMC strategy can increase the efficiency of PMSMs significantly, which verifies its effectiveness.
21 August 2015 in IEEE Transactions on Power Electronics
Active magnetic bearings (AMBs) have been proved superior to conventional bearings in many ways. However, the AMB system will lose magnetic force if the power fails which may cause fatal damage to the rotor and the backup bearings. In order to improve the reliability of the AMB system, a power failure compensation control (PFCC) method is proposed in this paper. A novel hardware composition of PFCC is designed to cooperate with the motor drives using either pulse-width modulation (PWM) or pulse-amplitude modulation techniques. Once the power fails, the motor works as a generator and the back electromotive force (back EMF) is rectified by the antiparallel diodes of the inverter. Meanwhile, a buck converter is utilized to convert the voltage from dc-link of the inverter to the supply voltage for the AMB system. When the motor speed is too low to supply high back EMF for the buck converter, the switches of the inverter are used to boost the dc-link voltage with the motor windings. Furthermore, a hybrid controller combining sliding mode control with PID algorithm is introduced to improve the transient response of the buck converter. Several experimental results confirm the feasibility and effectiveness of the proposed method.
Demagnetization fault diagnosis is a significant issue in magnetically suspended permanent magnet synchronous motor (PMSM). The occurrence of a permanent magnet (PM) demagnetization fault reduces the motor efficiency and even disables the whole power system. Unfortunately, it is challenging to extract the fault feature and evaluate the exact severity precisely due to the rich environmental noise and the coupling faults. This article proposes a novel strategy using the improved variational mode decomposition (VMD) and energy moment relative entropy (EMRE) to achieve the demagnetization fault diagnosis, facilitating the timely implementation of the corresponding control strategies. Firstly, the harmonic component caused by the demagnetization fault is studied. An improved VMD algorithm is proposed to preprocess the displacement signals and decompose them into a series of mutually-exclusive intrinsic mode functions (IMFs). Secondly, signal reconstruction is performed on the selected IMFs, and fault feature extraction is accomplished utilizing the Teager enhancement spectrum. Thirdly, EMRE is proposed as the evaluation indicator to evaluate the exact demagnetization severity. Finally, the system experimental platform with different demagnetization degree prototypes is constructed for validation.