The new generation of food packaging should not only be biodegradable, but also provide additional protective properties for packaged products, extending their shelf life. In this paper, we present the results of research on cast-extruded poly(butylene succinate) (PBS) films coated with hydroxypropyl methylcellulose (HPMC) modified with CO2 extract from sea buckthorn (ES) or its ethosomes (ET) at amounts of 1 or 5 pph per HPMC. In addition, the developed films were exposed to accelerated aging (UV radiation and elevated temperature) to determine its effect on the films’ properties. Based on SEM, it can be concluded that accelerated aging results in the uncovering of the extract and ethosomes from the coating’s bulk. GPC showed a decrease in the molecular weight of PBS after treatment, additionally amplified by the presence of HPMC. However, the addition of ES or ET in low concentrations reduced the level of polyester degradation. The presence of the modified coating and its treatment increased the oxygen barrier (a decrease from 324 cm3/m2 × 24 h for neat PBS to 208 cm3/m2 × 24 h for the coated and modified PBS ET5). Despite the presence of colored extract or ethosomes in the coating, the color differences compared with neat PBS were imperceptible (ΔE < 1). The addition of 5 pph of sea buckthorn extract or its ethosomes in combination with accelerated aging resulted in the complete inhibition of the growth of E. coli and S. aureus, which was not observed in non-aged samples. The results obtained demonstrate an improvement in bioactive properties and protection against the negative effects of UV radiation on the film due to the presence of ET or ES in the coating. The developed systems could be used in the food industry as active packaging.
The aim of the work was to obtain poly(butylene succinate)—a PBS biocomposite material with an addition of natural sodium montmorillonite (Na-MMT) modified with two selected terpenes: pinene (P) and limonene (L) or their mixture (PL)—and examine their physico-chemical, rheological, and antiviral properties. Na-MMT was effectively hydrophobized and intercalated (confirmed with FTIR, TGA, and XRD analysis results) with the terpenes via the solventless method. The materials were obtained via extrusion, and the films were formed using thermo-compression molding. The addition of the fillers slightly increased mechanical properties, but barrier properties towards oxygen and water vapor were significantly improved (OTR from 52 to 28 cm3/m2∙24 h and WVTR 21 to 11 g/m2∙24 h for PBS and composite, respectively) without alteration of polymer morphology (SEM, XRD, FTIR) or thermal and thermomechanical properties, despite high filler content (10 wt%) in the polymer matrix. Surface contact angle values of PBS/M, PBS/M-L, and PBS/M-PL exhibited antiviral properties and were tested using Φ6 bacteriophage. The composites can be used for materials in medical and food packaging applications.
The aim of the study was to modify polylactide with zinc oxide nanoparticles (ZnO), raspberry leaf extract (E), and a combined ZnO/extract system (EZnO) in order to prepare novel packaging materials via a solvent-free method, namely cast extrusion. Physicochemical properties: Morphology (GPC, SEM, FTIR), mechanical (tensile tests, puncture), barrier (WVTR, OTR, UV-Vis) and water contact angle for PLA-based films with two thickness ranges were investigated. Additionally, antimicrobial (antibacterial, antifungal and antiviral) tests were performed. GPC results revealed that the presence of the extract counteracted biopolyester degradation during hot melt processing. The best mechanical properties (TS ca. 50 MPa, EB ca. 18%) were obtained for PLA modified with raspberry leaf extract (PLA/E). EZnO addition led to the highest increase in oxygen (with 25%) and water vapor (up to ca. 28%) barrier properties. The material with EZnO addition was also found to be the only one to demonstrate antibacterial effectiveness, although the activity was insignificant. However, the incorporation of EZnO into the biopolymer matrix enhanced its antiviral properties, resulting in the complete inactivation of Φ6 bacteriophage particles used as a surrogate of SARS-CoV-2 virus.
The study investigated the antimicrobial and antiviral effects of polypropylene foil coated with hydroxypropyl methylcellulose (HPMC) layer containing tea tree oil (TTO) as the active agent. Moreover, the influence of accelerated aging using Q-SUN treatment on the efficacy of the non-coated and coated foils was also investigated. The results of the study indicated a slight antimicrobial effect of the irradiated coating against S. aureus, noticeable antibacterial activity of both irradiated and non-irradiated coating against E. coli and a complete inhibition of B. cereus growth by the irradiated coating. However, both of these coatings exhibited strong antiviral properties, confirmed by a method consisting of two separate tests conducted on the Φ6 phage as the infectious agent: real-time measurement of the host’s OD during co-culture with the phage and observation of the host’s growth on copper mesh grids using scanning electron microscopy (SEM). The characteristics of non-irradiated and irradiated foils were also determined using SEM and FT-IR.
Biofilm-forming microorganisms pose a severe threat in the food and medical industries, among others. In this paper, the research materials were poly(butylene succinate–dilinoleic succinate) (PBS–DLS) copolymers with variable hard and soft segment weight ratios (90:10, 70:30, and 50:50). Polymeric films were prepared by the solvent casting method. Selected physicochemical properties and the tendency to form biofilm on the polymer surface were investigated. As the amount of DLS soft segments in the polymer matrix increased, changes in the FTIR–ATR spectra (signal intensity), surface (SEM), and phase transition (DSC) were observed. The higher the content of the DLS segment, the lower the transition temperatures and the smoother the film’s surface. These factors resulted in a significant reduction in the amount of biofilm formed on the material’s surface and a decrease in the metabolic activity of microorganisms present in the biofilm and SEM micrographs. The obtained PBS–DLS films have great potential in the food and medical packaging industries.