This paper presents a high-sensitivity temperature and humidity synchronous measurement sensor based on virtual Vernier demodulation, designed to overcome the limitations of traditional sensors in high-sensitivity and synchronous measurements. By combining a dual-cavity parallel structure with the Virtual Vernier effect (VVE), two interferometers were designed, with one using a temperature-sensitive material (polydimethylsiloxane, PDMS) and the other using a humidity-sensitive material (polyvinyl alcohol, PVA) for temperature and humidity measurement, respectively. Based on actual interference spectra, a modulation function was used to generate the virtual reference interferometer spectrum, which was then superimposed with the sensing interferometer’s spectrum to form a virtual Vernier envelope. By monitoring the displacement of the envelope, precise measurements of temperature and humidity changes were achieved. Experimental results showed a temperature sensitivity of 5.61 nm/°C and 7.62 nm/°C, a humidity sensitivity of 0 nm/%RH and −3.07 nm/%RH, and average errors of 0.64% and 1.10% for temperature and humidity, respectively, demonstrating the feasibility of the method. The introduction of the virtual interferometer effectively reduces environmental interference with the measurement results and avoids the material loss and errors associated with traditional reference interferometers. More importantly, the VVE enables dynamic adjustment of the envelope magnification, thereby enhancing the sensor’s flexibility and overcoming the structural limitations of traditional interferometers. This sensor provides efficient and reliable technological support for future environmental monitoring and climate change research.

This paper presents a high-sensitivity multi-point seawater temperature detection system based on the virtual Vernier effect, achieved through multiplexed Fabry–Perot (FP) cavities combined with optical frequency-modulated continuous wave (FMCW) interferometry. To address the nonlinear frequency scanning issue inherent in FMCW systems, this paper implemented a software compensation method. This approach enables accurate positioning of multiple FP sub-sensors and effective demodulation of the sensing interference spectrum (SIS) for each FP interferometer (FPI). Through digital signal processing (DSP) algorithms and spectral demodulation, each sub-FP sensor generates an artificial reference spectrum (ARS). The virtual Vernier effect is then achieved by means of a computational process that combines the SIS intensity with the corresponding ARS intensity. This eliminates the need for physical reference arrays with carefully detuned spatial frequencies, as is required in traditional Vernier effect implementations. The sensitivity amplification can be dynamically adjusted with the modulation function parameters. Experimental results demonstrate that an optical fiber link of 82.3 m was achieved with a high spatial resolution of 23.9 $\mathsf{\mu }\mathrm{m}$. Within the temperature range of ${30 }^{\circ }\mathrm{C}$ to ${70 }^{\circ }\mathrm{C}$, the temperature sensitivities of the three enhanced EIS reached −275.56 $\mathrm{pm}{/}^{\circ }\mathrm{C}$, −269.78 $\mathrm{pm}{/}^{\circ }\mathrm{C}$, and −280.67 $\mathrm{pm}{/}^{\circ }\mathrm{C}$, respectively, representing amplification factors of 3.32, 4.93, and 6.13 compared to a single SIS. The presented approach not only enables effective multiplexing and spatial localization of multiple fiber sensors but also successfully amplifies weak signal detection. This breakthrough provides crucial technical support for implementing quasi-distributed optical sensitization sensing in marine environments, opening new possibilities for high-precision oceanographic monitoring.

This paper proposes a temperature-salt synchronous sensitisation detection technique based on data signal processing (DSP). The method first employs spectral analysis to decouple the independent interference spectra of each cavity from the combined interference spectrum of the parallel dual-cavity system. Subsequently, a virtual interferogram corresponding to each independent interferogram is constructed, and the two are superimposed to generate their respective vernier effect spectra. Finally, based on the relationship between the envelope peaks (or troughs) of the two vernier spectra and variations in temperature and salinity, a sensitivity matrix equation is established, thereby achieving highly sensitive simultaneous detection of temperature and salinity parameters. Experimental results indicate that within the temperature range of 21°C to 28°C, the temperature sensitivities of the dual-vernier spectrum are -2.0544 nm/°C and -4.9609 nm/°C, respectively, representing 8.08 times and 5.83 times the sensitivity of a single independent cavity. Within a salinity range of 20‰ to 50‰, the salinity sensitivities of the dual-vernier spectra were 1.4248 nm/‰ and 0, respectively, representing 7.98 times and 0 times the sensitivity of a single independent cavity. This method, requiring no physical interferometer and relying solely on algorithms, not only achieves simultaneous measurement of both temperature and salinity parameters but also realizes sensitivity amplification. This method offers simplicity of implementation, high sensitivity, and low cost, demonstrating promising application prospects in the field of high-sensitivity marine sensing.