Yajun Zhao

Dr. Yajun Zhao


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2019 in Materials Chemistry and Physics
Verified
Journal Article
Open access
QZQian Zhang
Qian Zhang
YLYing Liu
Ying Liu
TLTing Liao
Ting Liao
CZCaili Zhang
Caili Zhang
XWXiaolei Wu
Xiaolei Wu
PHPeide Han
Peide Han

1 March 2022 in Journal of Materials Science & Technology
Verified
Journal Article
Open access
QWQian Wang
Qian Wang
Shun XuShun Xu
Shun Xu
YZYajun Zhao
Yajun Zhao
Jean-Sebastien LecomteJean-Sebastien Lecomte
Jean-Sebastien Lecomte
CSChristophe Schuman
Christophe Schuman

24 December 2021 in Steel Research International
Verified
Journal Article
Closed access
PDF file
MQMuhammad Saqlain Qurashi
Muhammad Saqlain Qurashi
YZYajun Zhao
Yajun Zhao
CDChuang Dong
Chuang Dong
XZXiaoyang Zhang
Xiaoyang Zhang
LWLianchao Wang
Lianchao Wang
PWPeng Wan
Peng Wan

11 January 2022 in International Journal of Metalcasting
Verified
Journal Article
Closed access
PDF file
MQMuhammad Saqlain Qurashi
Muhammad Saqlain Qurashi
YZYajun Zhao
Yajun Zhao
CDChuang Dong
Chuang Dong
LWLianchao Wang
Lianchao Wang
YLYing Li
Ying Li

24 November 2021 in Materials
Verified
Journal Article
Open access
PDF file
HLHongming Li
Hongming Li
SZShuang ZHANG
Shuang ZHANG
YZYajun Zhao
Yajun Zhao
XLXiaona Li
Xiaona Li
FJFushi Jiang
Fushi Jiang
Chuang DongChuang Dong
Chuang Dong
Reaching simultaneously high mechanical strength and low electrical resistivity is difficult as both properties are based on similar microstructural mechanisms. In our previous work, a new parameter, the tensile strength-over-electrical resistivity ratio, is proposed to evaluate the matching of the two properties in Cu alloys. A specific ratio of 310 × 108 MPa·Ω−1·m−1, independent of the alloy system and thermal history, is obtained from Cu-Ni-Mo alloys, which actually points to the lower limit of prevailing Cu alloys possessing high strength and low resistivity. The present paper explores the origin of this specific ratio by introducing the dual-phase mechanical model of composite materials, assuming that the precipitate particles are mechanically mixed in the Cu solid solution matrix. The strength and resistivity of an alloy are respectively in series and parallel connections to those of the matrix and the precipitate. After ideally matching the contributions from the matrix and the precipitate, the alloy should at least reach half of the resistivity of pure Cu, i.e., 50%IACS, which is the lower limit for industrially accepted highly conductive Cu alloys. Under this condition, the specific 310 ratio is related to the precipitate-over-matrix ratios for strength and resistivity, which are both two times those of pure Cu.

5 May 2021
Verified
Conference Paper
Closed access
DWDongping Wang
Dongping Wang
CSChenglong Sun
Chenglong Sun
YZYajun Zhao
Yajun Zhao
SHSijun Huang
Sijun Huang
Nowadays, electric traction is applied in highspeed trains, and the effects of crosswind increase the instability of the pantograph turbulence, so higher requirements are put forward for the good contact between pantograph and catenary. A new type of pantograph of working height of 2800 mm and a running speed of 400 km/h was taken as the object in this study. Based on the three-dimensional, steady, incompressible N-S equation and k- $\omega$ SST (Shear Stress Transport) turbulence model, the variation of aerodynamic force and aerodynamic lift force with different crosswind speed and yaw angle were analyzed. The results show as follows: aerodynamic force and aerodynamic lift force of pantograph increase with increasing crosswind speed. The most dangerous situation of pantograph occurs while the crosswind speed is 30 m/s and the yaw angle is 60°, where the aerodynamic lift force is twice than without crosswind, and the flow field around the pantograph becomes more complicated, resulting in poor current collection between pantograph and catenary. Consequently, high-speed trains should slow down or stop running in the strong crosswind environment.