Chaoqun Sun

Prof. Dr. Chaoqun Sun

orcid

Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 October 2026 in Buildings
Verified
Journal Article
Open access
PDF file
CCChengyong Chen
Chengyong Chen
YLYoukai Li
Youkai Li
CXChangjing XU
Changjing XU
BWBaoqun Wang
Baoqun Wang
CSChaoqun Sun
Chaoqun Sun
To address the unclear relationship between overall deformation and local mechanical responses during the construction of composite linings consisting of precast inverts and cast-in-place arches in mining-method tunnels, this study takes Yaopocun Tunnel as the engineering case and uses field monitoring data from three typical cross-sections. Considering key construction stages, including invert segment assembly, base grouting, and casting of the secondary lining of the arch and walls, the spatiotemporal evolution of contact pressure between the invert and cushion layer, contact pressure between the secondary lining and primary support, reinforcement stress in the arch and walls, stress converted from concrete strain, and cross-sectional deformation is analyzed. The results show that variations in the contact pressure at the invert base exhibit temporal associations with construction equipment loading and subsequent secondary lining casting. The two types of interface contact pressure exhibited distinctly nonuniform distributions, with the mean monitored pressures during the later stage ranging from 30.39 to 36.47 kPa and from 52.67 to 85.16 kPa, respectively. In the later stages, the arch–wall reinforcement is predominantly under compression, with the absolute average compressive stress on the outer side being 1.32–1.99 times that on the inner side. Compressive stress is particularly pronounced at the wall feet. Although the strain-derived nominal stress responses of concrete were predominantly compressive, localized tensile responses were also identified, with a maximum calculated nominal tensile stress of approximately 2.34 MPa. The final crown settlement across the three sections ranges from 27.50 to 33.76 mm. Based on the normalized rate-of-change criterion, cross-sectional deformation entered a slowly varying stage approximately 4–5 days after invert excavation and rapid assembly, whereas interface contact pressure and lining material stress entered slowly varying stages approximately 24–40 days after subsequent secondary lining casting. These characteristic times were referenced to different construction events and do not indicate complete mechanical stabilization. These findings indicate that the overall deformation and local mechanical responses of composite linings with precast inverts exhibit distinct staged evolution patterns. A gradual stabilization of overall deformation does not necessarily indicate that subsequent adjustments in local mechanical responses have ended. During construction, attention should therefore be paid to stress variations at the wall feet and in localized tensile regions while controlling overall deformation.

1 April 2026 in Mechanics of Solids
Verified
Journal Article
Closed access
PDF file
CSChaoqun Sun
Chaoqun Sun
LZLu Zhang
Lu Zhang
NWNe Wang
Ne Wang
ZLZhipeng Li
Zhipeng Li
DWDeming Wang
Deming Wang
LZLuchen Zhang
Luchen Zhang
The soil pore ratio-pressure curve is an important factor in the calculation of foundation settlement by layer wise summation method. In order to establish the pore ratio-pressure curve analysis model of red clay in the whole process of lateral confined compression accurately, it is necessary to make a nonlinear correction to the analytical model of unloading rebound of red clay. Firstly, in the initial compression process of red clay, the stress-strain relationship of soil was assumed to obey the hyperbolic equation, and the analysis model of initial compression pore ratio and pressure curve of red clay was established. Secondly, according to the results of laboratory consolidation tests, the pore-pressure curve of red clay unloading rebound changes linearly when the unloading ratio is less than 0.5, and parabola changes when the unloading ratio is between 0.5 and 1.0. The piecewise function is used to characterize the unloading rebound process of red clay, and the second half of the unloading rebound curve of red clay is nonlinearly modified. Finally, the tangent modulus of the initial compressive stress-strain curve of red clay at the preconsolidation pressure was approximately equal to the secant modulus of the unloading rebound curve to calculate the initial pore ratio of recompressed soil, and then the analysis model of pore ratio and pressure curve of recompression of red clay was established. Through the comparison and analysis of theoretical calculation and measured results, the rationality of the pore ratio and pressure curve analysis model established in this paper is verified.

9 April 2026 in Materials
Verified
Journal Article
Open access
PDF file
JLJutong Li
Jutong Li
CSChaoqun Sun
Chaoqun Sun
YLYoukai Li
Youkai Li
CSChaoqun Sun
Chaoqun Sun
Mesoscale modeling provides an efficient and cost-effective approach for investigating the damage mechanisms of fiber-reinforced concrete. To address the physical distortion in conventional models that arises from neglecting the volumetric effect of steel fibers and to construct a more realistic random mesoscale model of steel fiber-reinforced concrete (SFRC), this study proposes an efficient modeling method based on geometric entity expansion and point–line topology. First, polygonal aggregates with diverse morphologies are generated using a polar-coordinate perturbation scheme combined with a convex-hull correction algorithm. Next, abandoning the traditional zero-thickness line-segment assumption, steel fibers are expanded into rectangular entities via rigid-body kinematics to explicitly represent their excluded volume. Furthermore, a vector-cross-product-based Point–Line Method is developed to replace conventional circumscribed-circle screening, enabling accurate discrimination of interference interactions between fiber–aggregate and fiber–fiber pairs. An automated framework—consisting of skeleton placement, entity generation, topological discrimination, and mesh mapping—is implemented through a Python 3.13.9 scripting interface, allowing efficient batch generation of high-content mesoscale models with aggregate area fractions up to 70%. The proposed model is then used to simulate the failure process of SFRC specimens under uniaxial compression and benchmarked against experimental results. The results show that the developed mesoscale model accurately reproduces the nonlinear mechanical response and the strengthening–toughening effects of SFRC, achieving a relative error of only 0.31% in peak stress and a root mean square error (RMSE) as low as 1.70 MPa over the full stress–strain curve. The simulations not only confirm the pronounced strength gain due to steel fiber incorporation (~19.7%), but also reveal, at the mesoscale, the mechanism by which fiber bridging suppresses damage localization, thereby demonstrating the reliability and practical effectiveness of the proposed modeling approach.