Contact curvature plays a pivotal role in the Young’s modulus determination and mechanical response of a particle. This paper presents the sensitivity analysis of a particle morphology to contact curvature and its influence on the Young’s modulus determination during the elastic deformation of a particle. X-ray computed micro-tomography (μCT) was conducted to obtain the prototype of a single particle. The digital information of the scanned particle, including 2D slices and 3D rendering was processed and the variation of contact curvature of the particle was examined using the circular (spherical at 3D) and polynomial fitting methods. The fitting sections of the particle are taken into account. The effect of contact curvature on Young’s modulus determination was investigated and it was found that Young’s modulus changed substantially from global fitting to local fitting. Young’s modulus is highly related to the surface roundness, which exerts a significant influence on the determination of Young’s modulus.
Modern construction extensively utilizes foam concrete (FC) because of its distinct characteristics. However, its application is limited by its low strength properties. Developing high-strength FC by strengthening the matrix with various additives and incorporating various types of fibers into the composition is one of the most rational trends, consistent with the concept of sustainable and environmentally friendly construction. This study explores the impact of diverse polymer fibers on the strength and deformation characteristics of fiber-reinforced foam concrete (FRFC). The concrete’s matrix is strengthened by a composite nanomodifying additive. A FEM model was developed, and experimental studies of the compressive and flexural strength of FRFC were conducted. In the numerical study, the FC matrix is described by the Menetrey-Willam model. Parameter calibration and model verification demonstrated good agreement with experimental data. Experiments and numerical simulations proved that polypropylene fibers enhance compressive strength by as much as 20% and flexural strength by 80%. The stress–strain condition of FRFC was numerically analyzed, considering the influence of steel, carbon, and glass fibers. It was shown that high-modulus polymer fibers quickly lose their adhesive properties and impair the deformation properties of the composite compared to polypropylene fibers.
Slurry shields maintain excavation face stability by forming a sealing filter cake through pressurized slurry filtration, though cutterhead rotation inevitably compromises this integrity. This study investigates seawater-based slurry filtration behavior under cutterhead disturbance using model testing, utilizing the effective support force conversion rate to quantify the filter cake formation efficiency. Quantitative analysis evaluated key slurry constituents—bentonite, carboxymethyl cellulose (CMC), and fine sand (content/particle size)—and operational parameters including cutterhead rotation speed, advance rate, and slurry pressure. Results demonstrate enhanced conversion rate and stability with increased bentonite, CMC, and fine sand content; reduced fine sand particle size; elevated slurry pressure; and decreased cutterhead speed/advance rate. Nonlinear relationships exist between bentonite content and fine sand particle size, on the one hand, and the mean conversion rate and its fluctuation range, on the other. Stratum permeability and slurry pressure exhibit nonlinear effects on fluctuation range but linear relationships with mean value, indicating marginal impacts on support force magnitude and operational stability. Sensitivity analysis confirms bentonite as the dominant influencing factor, followed by cutterhead speed and CMC.
The applicability of similar materials is a key factor affecting the results of geomechanical model tests. In order to investigate the multi-physical field evolution mechanism of surrounding rocks during water inrush disasters in tunnels crossing fault zones, based on the similarity theory of geomechanical model tests, the physical–mechanical parameters of a prototype rock’s mass were first analyzed for similarity, and the target values of similar materials were determined. Secondly, using sand as coarse aggregate, talcum powder as fine aggregate, gypsum and clay as binders, and Vaseline as a regulator, a fault-simulating material suitable for model tests was developed through extensive laboratory experiments. Finally, with material deformation characteristics and strength failure characteristics as key control indicators, parameters such as uniaxial compressive strength, permeability coefficient, unit weight, and elastic modulus are synergistically regulated to determine the influence of different component ratios on material properties. The experimental results show that the uniaxial compressive strength and permeability coefficient of similar materials are mainly controlled by gypsum and Vaseline. Cohesion is mainly controlled by clay and Vaseline. The application of this similar material in the model test of the tunnel fault water inrush disaster successfully reproduced the disaster evolution process of fault water inrush, meeting the requirements of the model test for similar materials of faults. Furthermore, it provides valuable guidance for the selection of similar materials and the optimization of mix proportions for fault disaster model tests involving similar characteristics.
The soil pore ratio-pressure curve is an important factor in the calculation of foundation settlement by layer wise summation method. In order to establish the pore ratio-pressure curve analysis model of red clay in the whole process of lateral confined compression accurately, it is necessary to make a nonlinear correction to the analytical model of unloading rebound of red clay. Firstly, in the initial compression process of red clay, the stress-strain relationship of soil was assumed to obey the hyperbolic equation, and the analysis model of initial compression pore ratio and pressure curve of red clay was established. Secondly, according to the results of laboratory consolidation tests, the pore-pressure curve of red clay unloading rebound changes linearly when the unloading ratio is less than 0.5, and parabola changes when the unloading ratio is between 0.5 and 1.0. The piecewise function is used to characterize the unloading rebound process of red clay, and the second half of the unloading rebound curve of red clay is nonlinearly modified. Finally, the tangent modulus of the initial compressive stress-strain curve of red clay at the preconsolidation pressure was approximately equal to the secant modulus of the unloading rebound curve to calculate the initial pore ratio of recompressed soil, and then the analysis model of pore ratio and pressure curve of recompression of red clay was established. Through the comparison and analysis of theoretical calculation and measured results, the rationality of the pore ratio and pressure curve analysis model established in this paper is verified.