Tae-Wook Na

Dr. Tae-Wook Na

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2021 in Materials Science and Engineering: A
Verified
Journal Article
Closed access
GHGukin Han
Gukin Han
KLKyuhong Lee
Kyuhong Lee
JYJin-Young Yoon
Jin-Young Yoon
TNTae-Wook Na
Tae-Wook Na
KAKanghwan Ahn
Kanghwan Ahn
Tea-Sung JunTea-Sung Jun
Tea-Sung Jun

1 December 2019 in Metals
Verified
Journal Article
Open access
PDF file
WLWon-Hyuk Lee
Won-Hyuk Lee
KPKi Beom Park
Ki Beom Park
KYKyung-Woo Yi
Kyung-Woo Yi
SLSung Yong Lee
Sung Yong Lee
Kwangsuk ParkKwangsuk Park
Kwangsuk Park
HKHyung Giun Kim
Hyung Giun Kim
V-Nb-Mo-Ta-W high-entropy alloy (HEA), one of the refractory HEAs, is considered as a next-generation structural material for ultra-high temperature uses. Refractory HEAs have low castability and machinability due to their high melting temperature and low thermal conductivity. Thus, powder metallurgy becomes a promising method for fabricating components with refractory HEAs. Therefore, in this study, we fabricated spherical V-Nb-Mo-Ta-W HEA powder using hydrogen embrittlement and spheroidization by thermal plasma. The HEA ingot was prepared by vacuum arc melting and revealed to have a single body-centered cubic phase. Hydrogen embrittlement which could be achieved by annealing in a hydrogen atmosphere was introduced to get the ingot pulverized easily to a fine powder having an angular shape. Then, the powder was annealed in a vacuum atmosphere to eliminate the hydrogen from the hydrogenated HEA, resulting in a decrease in the hydrogen concentration from 0.1033 wt% to 0.0003 wt%. The angular shape of the HEA powder was turned into a spherical one by inductively-coupled thermal plasma, allowing to fabricate spherical V-Nb-Mo-Ta-W HEA powder with a d50 value of 28.0 μm.

1 September 2023 in International Journal of Hydrogen Energy
Verified
Journal Article
Open access
THTaejun Ha
Taejun Ha
VSVivek Shukla
Vivek Shukla
TNTae-Wook Na
Tae-Wook Na
YCYoung Whan Cho
Young Whan Cho
Jin-Yoo SuhJin-Yoo Suh
Jin-Yoo Suh
YLYoung-Su Lee
Young-Su Lee

6 December 2022 in Metals
Verified
Journal Article
Open access
PDF file
KPKi Beom Park
Ki Beom Park
Julien O. FadonougboJulien O. Fadonougbo
Julien O. Fadonougbo
JBJong-Seong Bae
Jong-Seong Bae
GKGyu Byeong Kang
Gyu Byeong Kang
JCJong In Choi
Jong In Choi
HKHyung Giun Kim
Hyung Giun Kim
The nature of TiFe-based surface oxides and their evolution during conventional activation heat treatment were investigated in this study. The as-prepared TiFe alloy was found to possess an initial composite Ti and Fe amorphous surface oxide layer of about 6 nm. Depth profiling has shown that oxides steadily vanish with increasing depth, whereas metallic Fe contribution and mixed Ti oxides arise, before eventually being found in their metallic state at 7.5 nm. In situ XPS measurements, carried out to directly observe the evolution of oxides during the activation procedure, have indicated that the initial ternary oxide begins to transform to metallic Fe and mixed Ti oxides at a temperature as low as 200 °C. Consistent with the literature, the reduction of Ti oxides took a major turn at around 400 °C. Toward the end of the in situ measurements, oxygen was partially dissolved due to the limited measurement duration: TiO and metallic Fe remained beyond 400 °C. A similar overall reduction behavior was observed for the Ni- and Mn-substituted alloys, with a few subtle exceptions: Ni existed in its metallic state from 200 °C whereas Mn was reduced from Mn3+ to the Mn2+ state only beyond 400 °C due to a pronounced difference in the oxidation driving force of these two substitution metals.

27 October 2019 in Metals
Verified
Journal Article
Open access
PDF file
KPKi Beom Park
Ki Beom Park
JCJaeho Choi
Jaeho Choi
TNTae-Wook Na
Tae-Wook Na
JKJang-Won Kang
Jang-Won Kang
Kwangsuk ParkKwangsuk Park
Kwangsuk Park
HKHyung Giun Kim
Hyung Giun Kim
In this study, oxygen reduction behavior of TiH2 powders during dehydrogenation process was investigated based on thermodynamics. During the hydrogenation–dehydrogenation (HDH) method to fabricate Ti powder, TiH2 was formed from a Ti sponge through hydrogenation annealing, and was easily pulverized even by ball milling due to its brittle nature. The ball milling process caused an increase in the oxygen concentration from 0.133 to 0.282 wt %, and transmission electron microscopy and X-ray photoelectron Spectroscopy results demonstrated that the formation of oxide layers such as TiO and TiO2 formed on the surface of the TiH2 powder resulted in the higher oxygen content. Dehydrogenation, which is the process originally conducted to eliminate hydrogen from TiH2, was used to remove and/or reduce oxygen, resulting in the reduction of the oxygen concentration from 0.282 to 0.216 wt %. Thermodynamic calculations confirmed the possibility of oxygen reduction by atomic hydrogen but molecular hydrogen has no function for the oxygen reduction. Glow discharge mass spectrometry (GD-MS) analysis, which checks H2O flow as an evidence of the oxygen reduction by hydrogen, supported the fact that the atomic hydrogen formed during the dehydrogenation process is able to play a critical role in decreasing the oxygen content.

1 April 2016 in Scripta Materialia
Verified
Journal Article
Closed access
HSHyung-Seok Shim
Hyung-Seok Shim
TNTae-Wook Na
Tae-Wook Na
JCJin-Seok Chung
Jin-Seok Chung
SKSoo-Bin Kwon
Soo-Bin Kwon
KGKyehwan Gil
Kyehwan Gil
농문 황농문 황
농문 황