This paper presents a novel wireless sensor system that can be embedded in both glass and carbon fiber composites allowing for the first time to wirelessly measure pressure and temperature throughout the laminate during infusion, giving an insight into the process behaviour. The obtained data can be used for modelling the resin flow inside the composite, which is required for simulation and for speeding up the design of new parts. We suggest a system, which uses wireless data transmission that does not hurt the vacuum seal, even for sensors deeply embedded between conductive carbon fibers. The current sensor system gives an accurate pressure reading (mbar resolution) that provides information about the pressure gradient in the whole laminate. For carbon fibers, the sensors are soldered on a self-made, flexible, 10 μ-thick polyimide cable, which is resistant to high temperatures. This makes the system minimally invasive since only a 2mm × 2.5mm system remains inside the laminate.
27 December 2017 in Journal of Sandwich Structures & Materials
Carbon and glass dry fibre bundles were inserted into a ROHACELL® 71HERO polymethacrylimide foam core under a specific inclination angle and pin pattern in order to enhance the compressive strength and stiffness of the core material. Flatwise compression tests were conducted on pin-reinforced sandwich specimens and unreinforced sandwich to investigate the effect of pin volume fraction and pin material on the compressive mechanical properties and energy absorption characteristics. X-ray computed tomography was performed on tested specimens to investigate the failure modes under compressive loads. It was concluded that the compressive strength is mainly controlled by pin failure due to bending and compression loads at pin base. Moreover, increasing the pin volume fraction improved the compressive properties of the sandwich but using glass fibre pins instead of carbon fibre pins led to a higher increase of the absorbed crushing energy. Finally, an existing analytical model to predict the compressive strength and stiffness has been tested and evaluated.
Sandwich structures with a lightweight closed cell hard foam core have the potential to be used in primary structures of commercial aircrafts. Compared to honeycomb core sandwich, the closed cell foam core sandwich overcomes the issue of moisture take up and makes the manufacturing of low priced and highly integrated structures possible. However, lightweight foam core sandwich materials are prone to failure by localised external loads like low velocity impacts. Invisible cracks could grow in the foam core and threaten the integrity of the structure. In order to enhance the out-of-plane properties of foam core sandwich structures and to improve the damage tolerance (DT) dry fibre bundles are inserted in the foam core. The pins are infused with resin and co-cured with the dry fabric face sheets in an out-of-autoclave process. This study presents the results obtained from shear tests following DIN 53294-standard, on flat sandwich panels. All panels were manufactured with pin-reinforcement manufactured with the Tied Foam Core Technology (TFC) developed by Airbus. The effects of pin material (CFRP and GFRP) and pin volume fraction on the shear properties of the sandwich structure and the crack propagation were investigated and compared to a not pinned reference. It has been concluded that the pin volume fraction has a remarkable effect on the shear properties and damage tolerance of the observed structure. Increasing the pin volume fraction makes the effect of crack redirection more obvious and conserves the integrity of the structure after crack occurrence.
5 October 2020 in Journal of Thermoplastic Composite Materials
In the present paper, the influence of tailored load introduction inserts applied to a bolt-loaded open-hole injection plate with different short glass fibre content is investigated. The tailored load introduction inserts made with a Tailored Fibre Placement (TFP) process, as well as open-hole injection plates without an insert were considered as reference samples. The samples were tested under tensile bolt-loading. The influence of the TFP-inserts on the load bearing properties of the open-hole injection plates was investigated. The test results show a huge increase of the load-carrying ability of the short-glass-fibre specimens when TFP-inserts are integrated. Moreover, the damage tolerance was dramatically improved as the specimens with integrated TFP-inserts did not fail abruptly and a residual strength higher than the strength of the test specimen without insert could be observed. However, the strength of the test specimen with integrated insert did not exceed the strength of the insert itself in most cases.
Using piezoresistive pressure sensors and in-situ measurement of pressure gradient, the infusion of resin in fiber reinforced composite can be optimized. The optimization of resin flow in Vacuum Assisted Resin Infusion (VARI) is necessary to produce high-quality fibre-reinforced composites. To control the resin infusion process, piezoresistive pressure sensors areembedded to detect the resin flow and resin pressure in Carbon Fibre Reinforced Polymer(CFRP). The measured pressure validates the accuracy of analytical calculations, based on Darcy’s law in a porous medium. The sensors are of small size and therefore do not affect the natural flow of the resin.