Adverse events due to flow-induced blood damage remain a serious problem for blood pumps as cardiac support systems. The numerical prediction of blood damage via computational fluid dynamics (CFD) is a helpful tool for the design and optimization of reliable pumps. Blood damage prediction models primarily are based on the acting shear stresses, which are calculated by solving the Navier–Stokes equations on computational grids. The purpose of this paper is to analyze the influence of the spatial discretization and the associated discretization error on the shear stress calculation in a blood pump in comparison to other important flow quantities like the pressure head of the pump. Therefore, CFD analysis using seven unsteady Reynolds-averaged Navier–Stokes (URANS) simulations was performed. Two simple stress calculation indicators were applied to estimate the influence of the discretization on the results using an approach to calculate numerical uncertainties, which indicates discretization errors. For the finest grid with 19 × 106 elements, numerical uncertainties up to 20% for shear stresses were determined, while the pressure heads show smaller uncertainties with a maximum of 4.8%. No grid-independent solution for velocity gradient-dependent variables could be obtained on a grid size that is comparable to mesh sizes in state-of-the-art blood pump studies. It can be concluded that the grid size has a major influence on the shear stress calculation, and therefore, the potential blood damage prediction, and that the quantification of this error should always be taken into account.
In recent years, the design priorities of modern marine propellers have shifted from maximizing efficiency to minimizing vibration-induced noise emissions and improving structural durability. However, an optimized design does not necessarily ensure optimal performance across the full operational range of a vessel. Due to operational constraints such as reduced docking times and regional speed regulations, propellers frequently operate off-design. This deviation from the design point leads to periodic turbulent boundary layer separation on the propeller blades, resulting in increased unsteady pressure fluctuations and, consequently, elevated hydroacoustic noise emissions. To mitigate these effects, bio-inspired modifications have been investigated as a means of improving flow characteristics and reducing pressure fluctuations. Tubercles, characteristic protrusions along the leading edge of humpback whale fins, have been shown to enhance lift characteristics beyond the stall angle by modifying the flow separation pattern. However, their influence on transient pressure fluctuations and the associated hydroacoustic behavior of marine propellers remains insufficiently explored. In this study, we apply the concept of tubercles to the blades of a hubless propeller, also referred to as a rim-drive propeller. We analyze the pressure fluctuations on the blades and in the wake by comparing conventional propeller blades with those featuring tubercles. The flow fields of both reference and tubercle-modified blades were simulated using the Stress Blended Eddy Simulation (SBES) turbulence model to highlight differences in the flow field. In both configurations, multiple helix-shaped vortex systems form in the propeller wake, but their decay characteristics vary, with the vortex structures collapsing at different distances from the propeller center. Additionally, Proper Orthogonal Decomposition (POD) analysis was employed to isolate and analyze the periodic, coherent flow structures in each case. Previous studies on the flow field of hubless propellers have demonstrated a direct correlation between transient pressure fluctuations in the flow field and the resulting noise emissions. It was demonstrated that the tubercle modification significantly reduces pressure fluctuations both on the propeller blades and in the wake flow. In the analyzed case, a reduction in pressure fluctuations by a factor of three to ten for the different BPF orders was observed within the wake flow.
Even small amounts of entrained gas can reduce the acoustic wave speed in aliquid-filled pipe by an order of magnitude, pulling acoustic standing-waveresonances into the same frequency band as the spring-mass oscillation ofthe pipe on its supports.This paper develops a fully dimensionless Transfer Matrix Method (TMM)formulation for the axial vibration of thin-walled elastic pipes conveyingdilute dispersed bubble mixtures, modeling a representative inter-supportspan with finite-stiffness supports and anechoic fluid terminations. Theformulation reduces eleven physical primitives to six dimensionless groupsand a dimensionless support stiffness, and is validated againstexperimental data and verified against coupled acoustic-structural finiteelement analysis.A parametric study over 10000 Latin hypercube samples reveals thatonly four of the seven dimensionless groups form effective parametercombinations that govern the eigenfrequencies. A mode-crossingcriterion is derived that identifies the support stiffness atwhich the modal sequence reorders, a transition practically irrelevantfor single-phase liquids but essential when entrained gas is present.