Brent Keil

Brent Keil

Auto-generated profile, based on publicly available information

Brent Keil


Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2017 in Journal of Pipeline Systems Engineering and Practice
Verified
Journal Article
Closed access
SKSpyros A. Karamanos
Spyros A. Karamanos
GSGregory C. Sarvanis
Gregory C. Sarvanis
BKBrent D. Keil
Brent D. Keil
RCRobert J. Card
Robert J. Card
This paper offers an overview of available methodologies and provisions for the structural analysis and mechanical design of buried welded steel water pipelines subjected to earthquake action. Both transient (wave-shaking) and permanent ground actions (from tectonic faults, soil subsidence, landslides, and liquefaction-induced lateral spreading) are considered. In the first part of the paper, following a brief presentation of seismic hazards, modeling of the interacting pipeline–soil system is discussed in terms of either simple analytical models or more rigorous finite elements, pinpointing their main features. The second part of the paper outlines pipeline resistance, with emphasis on the corresponding limit states. Possible mitigation measures for reducing seismic effects are presented, and the possibility of employing gasketed joints in seismic areas is discussed. Finally, the discussed analysis methodologies and design provisions are applied in a design example of a buried steel water pipeline located in an area with severe seismic action.

11 July 2018
Verified
Conference Paper
Closed access
BKBrent D. Keil
Brent D. Keil
FGFritz Gobler
Fritz Gobler
RMRichard D. Mielke
Richard D. Mielke
GLGregory Lucier
Gregory Lucier
GSGregory C. Sarvanis
Gregory C. Sarvanis
SKSpyros A. Karamanos
Spyros A. Karamanos
Welded lap joints are commonly used in large-diameter steel pipelines for water transmission. Their structural performance constitutes a key issue for safeguarding pipeline structural integrity with no loss of pressure containment, required even after a severe seismic event. Full-scale experiments are presented herein, and are part of an extensive project sponsored and coordinated by Northwest Pipe Co. on the structural performance of welded lap joints under severe ground-induced (seismic) actions. In the companion paper “Numerical Simulation of Steel Lap Welded Pipe Joint Behavior in Seismic Conditions” numerical simulation of the experiments are presented. The paper describes a series of large-scale experiments on welded lap joints in 25.75 in outside diameter steel pipes, with wall thickness of 0.135 in (3 specimens) or 0.250 in (3 specimens). The specimens were internally pressurized to 40% of yield pressure, and then subjected to four-point bending. Measurements of the bending load, characteristic displacements, and local strains at the joint area are reported. In all tests, the welded lap joints tested were capable of sustaining remarkable bending deformation, without any loss of pressure containment. This behavior supports the argument that welded lap joints, if appropriately constructed, can be used in seismic areas where severe and permanent ground-induced actions in the pipeline may occur.

26 August 2010
Verified
Conference Paper
Closed access
RWReynold Watkins
Reynold Watkins
BKBrent Keil
Brent Keil
RMRich Mielke
Rich Mielke
SRShah Rahman
Shah Rahman
Bedding and backfill materials play a critical role in the long-term structural integrity of buried municipal pipelines. Soil strength is resistance to soil slip, and is a function of soil friction angle and any cohesion in the soil. It determines the stability of the soil. Soil stiffness is the modulus of soil elasticity, E', and is a function of soil type and the applied level of compaction. E' is also affected by depth of burial which increases confining pressure. E' determines the ring deflection of flexible rings. The Modified Iowa equation is used to predict ring deflection of buried flexible pipes. Common types of backfill material can range from native soils (which usually have fines, silt and clay) to imported crushed rock, to soil-cement slurry (or flowable fill/CLSM). Whenever backfill material other than native soils is specified on a project, the reason for doing so must be justified. This paper reviews and recommends best practices for the selection of common bedding and backfill materials for flexible pipes and conducts an economic analysis of the various options utilized. Theoretical aspects of pipe-soil interaction as it relates to ring deflection of pipe for various soil types are discussed.

11 July 2018
Verified
Conference Paper
Closed access
GCGiannoula Chatzopoulou
Giannoula Chatzopoulou
DFDimitris Fappas
Dimitris Fappas
SKSpyros A. Karamanos
Spyros A. Karamanos
BKBrent D. Keil
Brent D. Keil
RMRichard D. Mielke
Richard D. Mielke
The present paper reports numerical calculations which complement experimental work reported in the companion paper entitled “Experimental Results of Steel Lap Welded Joints in Seismic Conditions”, also presented in ASCE 2018 Pipelines Conference. Nonlinear finite element simulation tools are employed to investigate the bending capacity of internally-pressurized welded-lap 24-in-diameter pipeline joints, considering two thicknesses (0.135 in and 0.250 in). The work presented in this paper: (a) simulates numerically the seven large-scale experiments presented in detail in the companion paper; (b) elucidates some interesting issues of welded lap joint behavior under severe bending deformation. In the final part of the paper, based on the above experimental and numerical results, a discussion is offered on the design of welded lap joints in pipelines constructed in seismic areas.

30 July 2014
Verified
Conference Paper
Closed access
SCStuart G. Croll
Stuart G. Croll
CSC. Siripirom
C. Siripirom
BKB. D. Keil
B. D. Keil
Pull-off adhesion testing per ASTM D-4541 is a commonly used quality control check for coatings on large-diameter steel water pipe. During the testing a metal dolly is glued to a pipeline coating then pulled off to assess adhesion of the coating. In practice, results are very sensitive to circumstances and have large standard deviations compared with their mean value. It is clear from a simple inspection of Griffith's equation for the strength of materials that the pull-off stress at failure increases with the stiffness of the materials and the interfacial failure energy and is diminished by the presence of existing cracks or flaws. Finite element stress analysis explored the effect of the coating and glue stiffness and some of the other possible reasons for variation in the results, i.e., pipe curvature, misalignment of the dolly, and the effect of scoring through the coating and glue around the dolly. The tensile modulus of three polyurethane coatings, an epoxy adhesive, and a cyanoacrylate adhesive were measured and showed that it was possible for a polyurethane coating to be stiffer than an adhesive used to fix the dolly in place. The location of the maximum strain, in the glue or the coating, was used as an indicator of where the adhesive failure was likely to occur within the overall joint. Results indicate that the influence of dolly misalignment on the coated pipe is greater than the influence of the pipe curvature itself. If the dolly was aligned perfectly, the greatest strain and thus most likely location of failure was on the crest of the pipe at the pipe-coating interface. The value of the strain was not a strong function of the curvature of the underlying pipe surface. If the dolly was misaligned, then the locus of failure shifted to where the glue was thinnest, but remained at the coating-pipe interface, if the glue is stiffer than the coating. However, if the coating was stiffer than the glue, then the location of the two greatest strains indicated that failure was more likely to be at the glue-dolly junction in all cases, rather than at the coating-pipe interface. Users should be aware of how these, and other possible, variations affect the pull-off results if they rely upon single dolly pull values to assess the overall adhesion or use the test method to assess the likely reliability of a coated steel pipe in service.

11 July 2016
Verified
Conference Paper
Closed access
SKSpyros A. Karamanos
Spyros A. Karamanos
KAKonstantinos Antoniou
Konstantinos Antoniou
BKBrent Keil
Brent Keil
RCRobert J. Card
Robert J. Card
Using finite element simulation tools, which account for both geometric and material nonlinearities, the bending capacity of mitered steel pipe bends is investigated. First, numerical results are reported on the elastic behaviour of two steel typical grade 40 steel mitered elbows with D/t values equal to 192 and 240, with the purpose of calculating flexibility and stress intensity factors. Furthermore, the elastic-plastic response of the two bends is also examined towards identifying their ultimate capacity and the corresponding mode of failure. Internal pressure effects on the structural response are also examined. The present paper addresses some important features of mitered steel pipe elbow response that may arise in geohazard areas, towards safeguarding the structural integrity of steel water pipelines subjected to severe ground-induced actions.