Electrical discharge machining (EDM) is a highly precise technology that not only facilitates the machining of components into desired shapes but also enables the alteration of the physical and chemical properties of workpieces. The complexity of the process is due to a number of regulating factors such as the material of the workpiece and tools, dielectric medium, and other process parameters. Based on the material type, electrode shape, and process configuration, various shapes and degrees of accuracy can be generated. The study of erosion is based on research into processing techniques, which are the primary tools for using EDM. Empirical knowledge with subsequent optimization of technological parameters is one of the ways to obtain the required surface quality of the workpiece with defect minimization, as well as mathematical and numerical modeling of the EDM process. This article critically examines all key aspects of EDM, reflecting both the early foundations of electrical erosion and the current state of the industry, noting the current trends towards the transition of EDM to the 5.0 industry zone in terms of safety and minimizing the impact of the process on the environment.
In this study, the behavior of the spherical bearing component of the L-100 bridge part (AlfaTech LLC, Perm, Russia) is considered within the framework of a finite element model. The influence of the pattern of the coupling of the antifriction interlayer with the lower steel plate on the operation of the part is examined in terms of ideal contact, full adhesion, and frictional contact. The thickness of the antifriction interlayer varied from 4 to 12 mm. The dependencies of the contact parameters and the stress–strain state on the thickness were determined. Structurally modified polytetrafluoroethylene (PTFE) without AR-200 fillers was considered the material of the antifriction interlayer. The gradual refinement of the behavioral model of the antifriction material to account for structural and relaxation transitions was carried based on a wide range of experimental studies. The elastic–plastic and primary viscoelastic models of material behavior were constructed based on a series of homogeneous deformed-state experiments. The viscoelastic model of material behavior was refined using data from dynamic mechanical analysis over a wide temperature range [−40; +80] °C. In the first approximation, a model of the deformation theory of plasticity with linear elastic volumetric compressibility was identified. As a second approximation, a viscoelasticity model for the Maxwell body was constructed using Prony series. It was established that the viscoelastic model of the material allows for obtaining data on the behavior of the part with an error of no more than 15%. The numerical analog of the construction in an axisymmetric formulation can be used for the predictive analysis of the behavior of the bearing, including when changing the geometric configuration. Recommendations for the numerical modeling of the behavior of antifriction layer materials and the coupling pattern of the bearing elements are given in this work. A spherical bearing with an antifriction interlayer made of Arflon series material is considered for the first time.
Five modifications of polytetrafluoroethylene (PTFE) are considered as a modern alternative to PTFE as sliding layers of bridge bearing parts. Radiation-modified PTFE without additives and with nano-additives as well as composites based on PTFE with bronze inclusions and nanomodified carbon fiber fillers were investigated. Ultra-high-molecular-weight polyethylene (UHMWPE) and classic pure PTFE were considered as control samples. The thermomechanical properties of the materials were studied within the framework of dynamic mechanical analysis in the operating temperature range of bridge structures [−40; +80] °C. The exit zones from the linear theory of viscoelasticity were established for all the materials considered. Temperature dependencies of the storage modulus and the loss modulus were determined. Thermoviscoelastic models of material behavior were constructed using a numerical identification procedure, experimental data, and simulation models. The thermomechanics of materials during the deformation of the spherical support part of the bridge were analyzed. Temperature dependencies of the parameters of the contact stress-strain state were determined with an average coefficient of determination R2 = 0.97 and an average error size RMSE = 0.092.
1 February 2017 in IOP Conference Series: Materials Science and Engineering
The fundamentals of the geometric immersion stress method for axisymmetric problems of elasticity theory have been stated. The geometric immersion method involves reduction of the initial problem for Clapeyron's free form elastic body to an iteration sequence of elasticity theory problems on some canonical domain. The iteration procedure for the variational equation of the geometric immersion method has been stated, as well as its discrete analog construction technique suggested with the finite-element stress method for the axisymmetric problem of the elasticity theory in the cylindrical coordinates. A practical application of the method has been demonstrated by a test problem. A reasonably good fit between the stress fields definition and the numerical solution by the traditional finite-element displacement method has been obtained.
Five modifications of polytetrafluoroethylene (PTFE) are considered as a modern alternative to PTFE as sliding layers of bridge bearing parts. Radiation-modified PTFE without additives and with nano-additives, as well as composites based on PTFE with bronze inclusions and nanomodified carbon fiber fillers, were investigated. Ultra-high-molecular-weight polyethylene (UHMWPE) and classic pure PTFE were considered as control samples. The thermomechanical properties of the materials were studied within the framework of dynamic mechanical analysis in the operating temperature range of bridge structures [−40; +80] °C. The exit zones from the linear theory of viscoelasticity were established for all the materials considered. Temperature dependencies of the storage module and the loss module were determined. Thermo-viscoelastic models of material behavior were constructed using a numerical identification procedure, experimental data, and simulation models. The thermomechanics of materials during the deformation of the spherical support part of the bridge were analyzed. Temperature dependencies of the parameters of the contact stress-strain state were determined with an average coefficient of determination R2 = 0.97 and an average error size RMSE = 0.092.
In the study, the behavior of the spherical bearing component of the L-100 bridge part (AlfaTech LLC, Perm, Russia) is considered within the framework of a finite element model. The influence of the pattern of the coupling of the antifriction layer with the lower steel plate on the operation of the part is examined: ideal contact, full adhesion, frictional contact. The thickness of the antifriction layer varied from 4 to 12 mm. The dependencies of the contact parameters and the stress-strain state on the thickness were determined. Structurally modified polytetrafluoroethylene (PTFE) without AR-200 fillers was considered as the material of the sliding layer. The gradual refinement of the behavior model of the antifriction material to account for structural and relaxation transitions was carried out on the basis of a wide range of experimental studies. In the first approximation, a model of the deformation theory of plasticity with linear elastic volumetric compressibility was identified. As a second approximation, a viscoelasticity model for the Maxwell body was constructed using Prony series. It was established that the viscoelastic model of the material allows for obtaining data on the behavior of the part with an error of no more than 15%. The numerical analog of the construction in an axisymmetric formulation can be used for predictive analysis of the behavior of the bearing, including when changing the geometric configuration.