In this paper, a new Modified Single Switch Single Ended Primary Inductor Converter (MS2-SEPIC)-based high step-up DC-DC converter is presented. The proposed topology uses the coupled-inductor (CL) technique and a voltage tripler rectifier which result a high voltage gain for the converter. Here, the switching loss has been reduced significantly because of the owing to the quasi-resonance operation of the circuit created by the leakage inductance of the CL along with circuit capacitors. The operational principles and steady state analysis are discussed. Experimental results based on a 100W laboratory prototype verify the validity of theoretical analysis.
This study presents a novel single‐switch high step‐up dc–dc converter employing a quasi‐resonant operation with high efficiency and low ripple continuous input current characteristics. In order to achieve a high voltage gain, a combination of coupled inductor and switched capacitor techniques is used in the proposed dc–dc converter. Moreover, utilising a series resonance capacitor with the leakage inductance of the coupled inductor leads to a resonant circuit. Subsequently, by employing a quasi‐resonant operation, the switching loss of the proposed dc–dc converter has been reduced significantly. Operational analysis, mathematical derivation, component voltage and current ratings are well demonstrated in this study. Finally, the performance of the proposed circuit is evaluated through a 200 W laboratory prototype with 25 V input voltage and 400 V output voltage. The maximum efficiency achieved at full load is 96.4%.
25 December 2019 in IEEE Transactions on Power Electronics
A New Coupled-Inductor Buck-Boost Converter (CIBuBoC) is proposed in this paper. In the proposed CIBuBoC, an ultra-high step-up/step-down voltage conversion ratio and step-up/step-down boundary adjustment are achieved compared to the other related buck-boost converters using two power switches with simultaneous operation along with a coupled-inductor. This circuit has a simple structure with two cascade semi-stage and some features including ultra-extended output voltage, continuous input current with low ripple, the positive polarity of the output voltage and common ground. These features make the CIBuBoC more suitable for many applications such as photovoltaic (PV) systems. Moreover, the voltage stress across each power switches is much lower than the other buck-boost converters led to power MOSFETs selection with lower drain-source ON resistance (Rds). Therefore, the proposed converter has also enough high efficiency. All steady-state and stress analysis and also comparisons with other related converters in Continuous Conduction Mode (CCM) are provided in detail. Also, using the state-space averaging technique, the low-frequency behavior of the proposed CIBuBoC is studied completely. Experimental results of a 100W step-up 30V-200V and a 35W step-down 30V-22V confirm the theoretical advantages of the proposed circuit.
14 November 2022 in IEEE Transactions on Industrial Electronics
This article introduces a new nonisolated high-voltage-gain single-ended-primary-inductor-capacitor-based multiport dc–dc converter. The boosting structures, including voltage lift cell and coupled inductor, are employed to increase the voltage gain of the suggested converter, and also the input current of the proposed structure is continuous and has a low ripple, which is appropriate for renewable energy sources. Both the inputs of this converter can operate individually or simultaneously. This topology has three ports: the renewable energy source port, the battery port, which is a bidirectional port, and the output port. In this topology, the voltage stress of three MOSFET switches is low. The low-voltage stress of switches causes a reduction in their losses and improves the efficiency of this converter. Compared with converters with similar functionality, the minimum number of active switches is used in this structure, which causes reducing the implementation cost and the control structure's complexity. Operating modes of the new topology are explained in this article. Finally, a 100-W prototype of the introduced converter is accomplished to validate the claims.
To carry out stability and voltage regulation studies on more electric aircraft systems in which there is a preponderance of multi-pulse, rectifier-fed motor-drive equipment, average dynamic models of the rectifier converters are required. Existing methods are difficult to apply to anything other than single converters with a low pulse number. Therefore an efficient, compact method for deriving the approximate, linear, average model of 6- and 12-pulse rectifiers, based on the assumption of a small duration of the overlap angle is presented. The models are validated against detailed simulations and laboratory prototypes.
4 March 2019 in International Journal of Circuit Theory and Applications