Yunpeng Cui

Dr. Yunpeng Cui


Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 October 2025 in Materials
Verified
Journal Article
Open access
PDF file
CWChangqing Wu
Changqing Wu
YYYuanquan Yang
Yuanquan Yang
YCYunpeng Cui
Yunpeng Cui
YCYunpeng Cui
Yunpeng Cui
Fly ash is a commonly used mineral addition in construction engineering. Research on its different particle size distributions can help optimize material performance, promote resource utilization, and support environmental protection. In this study, the particle size of fly ash was used as a variable; fly ash with a single particle size was prepared by means of sieving, and the particle size was precisely controlled as a variable, thus avoiding the errors caused by the addition of multiple different particle sizes. Replacing 10% of the cement with fly ash to prepare cement mortar, the influence of fly ash particle size on the performance of cement mortar was investigated. The results show that the mortar incorporating fly ash with a particle size range of 10–20 μm achieves a 28-day compressive strength of 58.25 MPa and a flexural strength of 10.29 MPa. The hydration heat release rate of fly ash in the 10–20 μm range reaches a maximum of 1.84 mW/g, and the total hydration heat release peaks at 211.17 J/g at 70 h. The influence of fly ash particle size on the total hydration heat release is relatively small in the early stages but increases rapidly with prolonged hydration time. When the fly ash particle size is in the 10–20 μm range, the cement mortar exhibits the lowest total porosity at 12.88%, with the smallest average pore size of 27.1 nm and the smallest most probable pore size of 21.2 nm. This reduces harmful pores, increases the number of harmless pores, makes the cement mortar structure denser, and improves the durability of the mortar. The types of hydration products of different particle sizes of fly ash did not change. The smaller the particle size of fly ash, the more complete the volcanic ash reaction, promoting the hydration of mortar.

24 November 2025 in Materials
Verified
Journal Article
Open access
PDF file
YCYunpeng Cui
Yunpeng Cui
RLRunqing Liu
Runqing Liu
YYYuanquan Yang
Yuanquan Yang
YCYunpeng Cui
Yunpeng Cui
This study investigates the performance variations in chemically bonded phosphate ceramic (CBPC) cement under different media (water and 3% NaCl solution) environments subjected to varying numbers of freeze–thaw cycles, including changes in compressive strength, mass loss rate, phase composition, microstructure, external pH, and ion concentration, with the aim of elucidating its long-term durability degradation mechanisms and microstructural evolution. The results show that both the mass and compressive strength of CBPC cement first increase and then decrease with increasing freeze–thaw cycles. After 400 cycles, the compressive strength decreases by 29.91% in water and 25.16% in salt solution. The pH value rises with cycling, along with increased concentrations of K+, Mg2+, and PO43−, while Na+ and Cl− concentrations decrease in salt solution. XRD/Rietveld analysis reveals that the content of MgKPO4·6H2O decreases from 28.1% to 19.5% (water) and 20.7% (salt), with a gradual reduction in crystallinity. TG/DTG and FTIR results confirm these findings, showing extensive microcracking in hydration products, which aligns with the observed macro-performance changes.

29 March 2026 in Materials
Verified
Journal Article
Open access
PDF file
YYYuanquan Yang
Yuanquan Yang
XYXioayu Ying
Xioayu Ying
HHHao Huang
Hao Huang
YCYunpeng Cui
Yunpeng Cui
Magnesium potassium phosphate cement (MKPC) is a promising bone repair material but suffers from excessively rapid setting time (typically within minutes) that limits clinical application. This study systematically investigates trimagnesium phosphate (TMP) as a candidate retarding additive for MKPC. TMP was used to partially replace dead-burned magnesium oxide at replacement levels of 0%, 10%, and 15% by mass. The effects of TMP content, water-to-cement ratio (0.17–0.23), and magnesium-to-phosphate molar ratio (4–10) on setting time, fluidity, hydration kinetics, compressive strength, and microstructure were comprehensively evaluated. Results show that TMP effectively extends the setting time from 9–13 min (without TMP) to 10–19 min, providing a working window that may be suitable for biomedical applications requiring extended handling time. Notably, 10% TMP incorporation enhances early compressive strength, with 1-day strength reaching 35.2 MPa compared to 28.5 MPa for control samples. Hydration heat analysis reveals TMP moderates the acid-base reaction kinetics through its slower dissolution rate compared to MgO. Microstructural characterization shows TMP promotes the formation of denser K-struvite crystals with refined microstructure. The optimal TMP dosage of 10% achieves a balanced performance, extending setting time while improving early strength and microstructural densification. These findings establish TMP as an effective retarder for developing MKPC-based materials with potential for biomedical applications, pending further biological validation.

28 March 2026 in Materials
Verified
Journal Article
Open access
PDF file
YCYunpeng Cui
Yunpeng Cui
RLRunqing Liu
Runqing Liu
YYYuanquan Yang
Yuanquan Yang
YCYunpeng Cui
Yunpeng Cui
YWYihe wang Wang
Yihe wang Wang
Magnesium phosphate cement (MPC) is a type of rapid-hardening inorganic cementitious material, which has important application value in rapid road repair, solidification of hazardous and radioactive waste, and other fields. However, it suffers from excessively fast setting and hardening and a short working time retention, which severely restrict its engineering application. Therefore, the development of high-efficiency set retarders is of great significance for optimizing MPC performance, enhancing its construction workability, and expanding its application scope. In this study, the effect of sodium polyacrylate (PAAS) on the setting and hardening of magnesium potassium phosphate cement (MKPC) was investigated by testing the setting time and fluidity at a low water-to-solid ratio (W/S = 0.18). Through pH and electrical conductivity measurements, combined with XRD, TG/DTG, and FTIR characterizations, we elucidated the retarding mechanism of PAAS on MKPC using a high water-to-solid ratio (W/S = 10). The results indicate that the setting time of MKPC is positively correlated with the PAAS dosage, whereas the fluidity and compressive strength exhibited a negative correlation with the PAAS dosage. Additionally, PAAS reduces the total heat release and the heat release rate of MKPC. The addition of PAAS increased the pH of the suspension, thereby reducing the solubility of MgO, but did not inhibit the dissolution of KH2PO4. The carboxylate groups in PAAS chemically reacted with Mg2+ on the surface of MgO to form magnesium carboxylate complexes (Mg-PAA), which remained as precipitates in the MKPC suspension system, thus reducing the amount of available Mg2+ participating in the hydration reaction. Furthermore, PAAS had no effect on the final precipitate composition at the end of hydration, which was composed of MgKPO4·6H2O and Mg3(PO4)2·22H2O in all cases.