Hongwen Jing

Prof. Hongwen Jing


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 February 2019 in Rock Mechanics and Rock Engineering
Verified
Journal Article
Closed access
PDF file
QYQian Yin
Qian Yin
Richeng LiuRicheng Liu
Richeng Liu
HJHongwen Jing
Hongwen Jing
HSHaijian Su
Haijian Su
LYLiyuan Yu
Liyuan Yu
LHLixin He
Lixin He

15 March 2017 in Acta Mechanica Sinica
Verified
Journal Article
Closed access
PDF file
HSHaijian Su
Haijian Su
HJHongwen Jing
Hongwen Jing
QYQian Yin
Qian Yin
LYLiyuan Yu
Liyuan Yu
YWYingchao Wang
Yingchao Wang
XWXingjie Wu
Xingjie Wu

1 September 2018 in Processes
Verified
Journal Article
Open access
PDF file
Qian YinQian Yin
Qian Yin
LHLixin He
Lixin He
HJHongwen Jing
Hongwen Jing
DZDong Zhu
Dong Zhu
The existence of surface roughness, various contact conditions and the occurrence of flow nonlinearity make the flow process in natural rock fractures more complicated. To evaluate the fluid flow regimes in deformable rough-walled rock fractures, a great many hydromechanical tests were conducted on nine real fractures artificially produced from a wide range of lithological diversity. For fractures with a certain JRC (fracture roughness coefficient) value, the confining pressure varied from 5 to 20 MPa, and the hydraulic pressure was increased from 0.4 to 6.0 MPa. The experimental results display that (i) regression analyses of the raw experimental data indicate that the Forchheimer’s law provides a perfect description for flow process through the fractures. The coefficients of viscous and inertial pressure drops undergo a growth of 2–3 orders of magnitude with an increase in the confining pressure; (ii) the hydraulic aperture decreases by approximately 87.41–92.81% as the confining pressure increases, and experiences a decrease of 1.52–2.96 times with the JRC values. A power-law function is used to evaluate the hydraulic aperture as a function of the nonlinear coefficient. The nonlinear coefficient decreases with increasing hydraulic aperture; (iii) using Forchheimer equation, the critical Reynolds number Rec was successfully assessed by choosing E percentage (generally 10%) of the nonlinear effect as the critical value between the linear and nonlinear flow regimes. The obtained Rec steadily increases with increasing confining pressure, while it diminishes with the JRC values; and (v) the transmissivity decreases as the pressure gradient increases. Additionally, transmissivity also exhibits a decreasing trend with both the confining pressures and JRC values due to fracture closure and tortuous and channeling flow paths in rougher fractures, and the rate of its decrease for a smaller confining pressure (5, 10 MPa) is more significant.


8 August 2019 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PDF file
BMBo Meng
Bo Meng
HJHongwen Jing
Hongwen Jing
WZWenxin Zhu
Wenxin Zhu
HSHaijian Su
Haijian Su
Water-rock interaction is a vital factor to affect the stabilities of rock projects. This paper conducted a series of experiments on argillaceous limestones to investigate the influences of saturation and wetting-drying cycle on the physical and mechanical performances of rocks. The results show that the increasing saturation increases the dissolution of clay minerals and lubrication among mineral grains, resulting in an obvious reduction effect on the strength and deformation performances of argillaceous limestones. Wetting-drying cycle increases the porosity and changes the pore structure of argillaceous limestones, leading to the pore transformation from small pore (0.01∼0.1 μm) to relatively large pore (0.1∼1.0 μm). Both the physical and mechanical performances of argillaceous limestones are weakened by the wetting-drying cycle. Besides, the variation process of the physical and mechanical parameters, including mass loss, density, ultrasonic velocity, compression strength, peak strain, elasticity modulus, and secant modulus, can be divided into two stages: 0∼6th wetting-drying cycle, gently changing, and 6th∼12th wetting-drying cycle, drastically changing. The whole change process of these physical and mechanical parameters with the increase in the wetting-drying cycle number can be expressed with the exponential function in general.

3 May 2018 in Latin American Journal of Solids and Structures
Verified
Journal Article
Open access
PDF file
Liyuan YuLiyuan Yu
Liyuan Yu
HSHaijian Su
Haijian Su
Richeng LiuRicheng Liu
Richeng Liu
HJHongwen Jing
Hongwen Jing
GLGuanglei Li
Guanglei Li
Ming LiMing Li
Ming Li
Thermal damage in rock engineering occurs in the air-filled and quasi-vacuum environments of rock mass located near or far from the free surface. Meanwhile, dynamic loads are encountered frequently in engineering practice. In this study, 39 limestone samples are prepared, and a series of laboratory tests, including split Hopkinson pressure bar (SHPB), nuclear magnetic resonance (NMR) and optical microscopy analyses, are conducted to investigate the effects of temperature and the environment on the dynamic mechanical properties of limestone. The results show that the macro-physical and dynamic mechanical properties of limestone after thermal treatment can be divided into two stages by a critical temperature of 450°C, at which the thermal damage factor is 0.71 and 0.75 in the quasi-vacuum and air-filled environments, respectively. In the first stage, with temperatures varying from 25°C to 450°C, the thermal damage due to expansion and fracturing slightly influences the related parameters, except the P-wave velocity. However, in the second stage, with temperatures ranging from 450°C to 900°C, the thermal damage caused by mineral decomposition and hydration leads to a remarkable decrease in the dynamic bearing and anti-deformation capacities. The environment plays a negligible role in the first stage but an important role in the second stage, and the dynamic compressive strength and modulus of samples after thermal treatment in the air-filled environment are much lower than those in the quasi-vacuum environment. Both the temperature and environment of thermal treatment should be considered in engineering practice, especially when the temperature exceeds 450°C.