1 January 2018 in Advances in Materials Science and Engineering
To reveal the mechanism of water inrush in a fault tunnel and study the influence of different structures on the seepage process, a filling structure composed of a soil skeleton (fixed particles), a movable particles phase, and a water phase is constructed to simulate the rock mass broken by the fault. Fluent software is used to simulate the migration of the water phase in three different filling structures under different initial water velocities and dynamic viscosities. The variation law of the seepage time with the initial water velocity and dynamic viscosity in the three types of filling structures is obtained. The research shows the following: (1) the looser the filling structure, the greater the influence of gravity on the water phase seepage; the more compact the filling structure, the greater the spread range of the water phase and the more uniform the spread of the water phase. (2) The seepage time decreases with the increase in the initial water velocity. The seepage time and initial water velocity can be fitted by an exponential function. The effect of initial water velocity on seepage time is much greater than that of the structure. (3) The seepage time is related to both the dynamic viscosity and the structure. The seepage time increases with the increase in dynamic viscosity.
1 February 2021 in International Journal of Geomechanics
The shear behavior of intact cubic sandstones was studied under constant normal stiffness (CNS) conditions using self-designed equipment. A series of direct shear tests on intact sandstone blocks was conducted with initial normal forces of 0, 20, 40, 60, and 80 kN at a constant normal stiffness of 400 kN/mm that came from the sandstone specimen. The results show that the deformation of intact sandstones at the prepeak elastic stage is independent of the boundary condition. The progressive shear failure process of intact sandstone specimens under the CNS condition can be divided into three stages: the prepeak stage including the prepeak elastic stage and the prepeak yielding stage; the postpeak shear wear stage; and the residual shear sliding stage according to the relationship between shear stress and normal stress. Under the condition of CNS, shear yielding failure occurs in the prepeak stage, while under the condition of constant normal load (CNL), no obvious shear yielding failure was observed. Under the condition of CNS, normal force would not stop increasing due to normal dilation after failure of some local positions in the shearing process until complete coalescence of the failure plane. The higher the initial normal force, the closer the peak shear strength point of specimens under the CNL condition approaches the yielding point of specimens under the CNS condition. Under the condition of CNS, the shear failure surface of intact sandstone is mainly formed by tension in the prepeak shear stage. The shear failure apparent friction angle at shear wear stage is smaller than the basic friction angle at residual shear sliding stage and decreases with the increase of the normal stress. The specimens under the CNS condition have a unified basic friction angle in the residual shear sliding stage regardless of the initial normal force.
1 January 2018 in Advances in Civil Engineering
The shear behavior of concrete blocks reinforced by fully grouted bolts with different diameters was studied in this paper. More than 90 intact cubic samples (100 mm × 100 mm × 100 mm) with bolts ranging from 2 mm to 5 mm in diameter were tested at a constant stain rate of 0.5 mm/min. An oblique shear apparatus, which could simultaneously apply shear and normal force on tested samples at three slope angles (53°, 58°, and 63°) of a predetermined shear plane, was employed. The results indicate that the bolt has no evident influence on the shear behavior of intact concrete blocks at the prepeak shear strength stage. The bolt could significantly reduce the shear strength drop in the peak shear strength of the concrete block and contribute to reserving the residual shear strength of concrete blocks, especially at steep slope angles of the shear failure plane. The shear resistance provided by the bolt to the concrete block at the residual shear slip stage has a positive relationship with the diameter. The bolt with a larger diameter inflected in the vicinity of the shear failure plane of concrete block at the postpeak shear strength stage; additional normal force and direct shear resistance could still be persistently provided. Two empirical equations of the apparent cohesion and apparent internal angle of the bolted concrete block were obtained by linear regression considering rb, which is the ratio of the cross‐sectional area of the bolt to that of the bolted concrete block.
8 August 2019 in Advances in Materials Science and Engineering
Water-rock interaction is a vital factor to affect the stabilities of rock projects. This paper conducted a series of experiments on argillaceous limestones to investigate the influences of saturation and wetting-drying cycle on the physical and mechanical performances of rocks. The results show that the increasing saturation increases the dissolution of clay minerals and lubrication among mineral grains, resulting in an obvious reduction effect on the strength and deformation performances of argillaceous limestones. Wetting-drying cycle increases the porosity and changes the pore structure of argillaceous limestones, leading to the pore transformation from small pore (0.01∼0.1 μm) to relatively large pore (0.1∼1.0 μm). Both the physical and mechanical performances of argillaceous limestones are weakened by the wetting-drying cycle. Besides, the variation process of the physical and mechanical parameters, including mass loss, density, ultrasonic velocity, compression strength, peak strain, elasticity modulus, and secant modulus, can be divided into two stages: 0∼6th wetting-drying cycle, gently changing, and 6th∼12th wetting-drying cycle, drastically changing. The whole change process of these physical and mechanical parameters with the increase in the wetting-drying cycle number can be expressed with the exponential function in general.
27 June 2019 in KSCE Journal of Civil Engineering
In this paper, the influence of bolting on shear mechanical behavior of cement mortar specimens were studied. First, a shear test apparatus which could provide CNS (constant normal stiffness) condition was designed. Then, more than 140 bolted and non-bolted cement mortar blocks (100 × 100 × 100 mm) were prepared. The strengthening effect of bolts with diameters of 0–10 mm on cement mortar specimens was studied under different initial normal loads ranging from 20 kN to 60 kN and constant normal stiffness of 420 kN/mm. Two simplified models of shear behavior of reinforced cement mortar blocks were proposed. The most important influence of bolt on the cement mortar blocks was to strengthen the post-peak shear strength rather than the peak shear strength, and the strengthening effect was reduced under high initial normal force. The cohesion of cement mortar blocks was reduced while internal friction angle was increased in residual sliding stage by bolts. The dilation of reinforced cement mortar specimens in post-peak shear stage was significantly reduced due to bolting, and the larger the bolt diameter, the greater the reduction in the block dilation.