In this study, the particle size distribution and chemical composition of gold mine tailings were examined experimentally. A series of viscosity and uniaxial compressive strength (UCS) tests were used to study the relations between the viscosity of cemented tailings backfill (CTB) slurry, the solid content (SD), and the cement-to-tailings ratio (c/t). Relations between UCS performance of CTB and SD, c/t, and curing time (CT) were discussed while examining the microstructure of 28-day cured backfill with different solid contents. Results illustrate that a major increase in CTB viscosity by increasing the SD leads to the formation of tailings grains for a skeleton formation, which is formed due to consolidation and gravitational forces. The CTB’s strength increases with the increase of c/t, SD, and CT, due to a decrease in water-to-cement ratio and porosity, and an increase in hydration products over time. The SEM micrographs show how CTB’s microstructure is affected by the SD, generating ettringites and calcium silicate hydrates in the backfill matrix. The findings of this study will lead to an efficient CTB mix design for reaching the higher performance in underground mining structures, thereby reducing expenses related to the backfill.
With the use of glauberite mineral (GM) and sodium hydroxide (SH) alkaline catalysts to stimulate slag powder’s internal cementation activity and incorporate the two fine-grained solid wastes, such as quicklime (Q) and desulfurized ash (DA), a new cementitious material suitable for mine tailings was developed to replace traditional ordinary Portland cement (OPC) for reducing cement-related costs. A series of uniaxial compressive strength (UCS) tests were carried out on cemented tailings backfill (CTB) samples containing different activators. The results showed that (1) the highest UCS values of 14-day and 28-day cured CTB samples were 1.259 MPa and 2.429 MPa, respectively, and the effect of different activator types was in the order of SH > GM > DA > Q and SH > GM > Q > DA; (2) the relationship between UCS and activator dosages followed the function y = ax3 − bx2 + cx − d. Compared with the OPC 32.5 R cemented samples, the minimum strength growth factor was 1.45, and the maximum reached 2.03; (3) the optimal proportion of DA slag formula was 4.5% or 5.0% Q, 19% DA, 2.5% GM, and 0.7% SH. The aforesaid new cementitious materials met the mine’s UCS requirements with a relatively low cost (17.04–17.20 €/ton) and solved the stacking problem of solid wastes on the surface well. Ultimately, this study provides a useful reference for the development of mineral binders.
25 December 2016 in Advances in Materials Science and Engineering
To explore the influence that filling interval has on the mechanical strength of layered cemented tailing backfill (LCTB), uniaxial compression test is conducted on LCTB samples with a concentration of 70%, 72%, and 75% and a filling interval of 12 h, 24 h, 36 h, and 48 h. From the tests above, mechanical properties and failure modes of LCTB are acquired. The results are as follows: (1) The peak compressive strength of LCTB decreases as the filling interval increases, and it increases when the concentration grows with a certain length of filling interval. At the same time, the peak compressive strength and filling interval show polynomial distribution. (2) There are four stages during the loading process of cemented backfill specimen, that is, compression stage, linear elastic stage, crack extension stage, and undermines development stage. As the filling interval increases, CTB shows a failure mode of tensile failure-tensile shear failure transition-tensile and shear mixing destruction, which provides a theoretical basis for strength design and stability control of backfill.
1 January 2016 in Advances in Materials Science and Engineering
The relations among the uniaxial compressive strength of cemented paste backfill (CPB) with solid phase mass fraction, cement sand ratio, and curing age were studied. The UCS of CPB samples increased exponentially with the increase of solid phase mass fraction and curing age but increased linearly with the increase of cement sand ratio. The results of X-ray diffraction (XRD) and scanning electron microscope (SEM) showed that the strength was determined by the amount of ettringite and C-S-H gelling. With the increase of ettringite and C-S-H gelling, the strength became larger. The triaxial compression test was conducted by selecting four kinds of CPB samples. The results showed that, with the increase of confining pressure, peak and residual strength became larger, but the elastic modulus decreased. When the ratio of confining pressure and uniaxial strength is about 1 : 2, the CPB samples show significant ductility characteristics and the ratio of residual strength and peak strength increased obviously.
In recent years, cemented tailings/paste backfill (CPB) become more and more important to maintain mine structure and keep mining stope to be stable in deep underground mining. Deep mining process often accompanied by blasting, rock burst and other high-speed dynamic loading. So it’s important to make research on dynamic behavior and characteristics of CPB. In this paper, a series of dynamic loading tests on CPB specimens by SHPB were taken to study the characteristic of stress-strain, dynamic strength, deformation and failure of CPB. The experimental results revealed that some CPB specimens have 1~2 lower stress peaks after reaching the peak stress before getting completely failed. The greater the cement-sand ratio was, the more obvious of strain reaction was. This property mainly showed like follows. The greater the cement-sand ratio was, the greater the dynamic compressive strength was under similar velocity impact; the dynamic compressive strength and the average strain rate were quadratic equation relationship, and the greater the cement-sand ratio was, the higher increase rate of dynamic compressive strength caused by strain rate. The dynamic compressive strength enhancement factor increased with the increase of the strain rate, and is larger than that of rock samples. The failure forms of CPB specimens under low-speed impact were almost the same as them under static uniaxial and triaxle compression. The CPB specimens were crushed broken under the critical strain rate, similar to the failure mode of low strength concrete. The experimental research results will improve our understanding the dynamic mechanical property of CPB and help to guide the strength design of deep mining backfill.