Gongning Li

Gongning Li


Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 October 2025 in Lubricants
Verified
Journal Article
Open access
PDF file
KHKun Huang
Kun Huang
GLGongning Li
Gongning Li
XCXiang-dong Chang
Xiang-dong Chang
ZZZhou Zhou
Zhou Zhou
YPYuxing Peng
Yuxing Peng
RDRan Deng
Ran Deng
As a critical load-bearing component in mine hoisting systems, the service performance and lifespan of wire ropes are limited by the fretting wear behavior among their internal wires and strands. To investigate the effect of fretting parameters on the wear mechanisms in wire ropes, this paper systematically conducts fretting wear experiments on multi-wire contact pairs under varying fretting frequencies and tensile loads. The results show that as the fretting frequency increases from 0.5 Hz to 3.0 Hz, the coefficient of friction (COF) rises, with its steady-state value reaching approximately 0.65. Conversely, as the tension decreases from 150 N to 90 N, the COF increases, attaining a steady-state value of 0.71. The slip regime between the steel wires evolves from gross slip to partial slip with increasing frequency. With an increase in tensile load, the slip regime transitions from gross slip to partial slip and finally to adhesion. Higher fretting frequencies and greater tensile loads exacerbate both the wear rate and the severity of damage on the spiral contact wires inside the hoisting rope. The highest wear rate, 27.2 × 10−6 mm3/N·m, is observed at 3.0 Hz, while the maximum wear rate under tension is 39.6 × 10−6 mm3/N·m at 150 N. The dominant wear mechanisms at higher frequencies are abrasive wear, tribochemical reaction, and surface fatigue. Under greater tension, the primary wear mechanisms are abrasive wear, surface fatigue, and tribochemical reaction.

30 January 2026 in Lubricants
Verified
Journal Article
Open access
PDF file
LXLeyan Xia
Leyan Xia
GLGongning Li
Gongning Li
KHKun Huang
Kun Huang
YPYuxing Peng
Yuxing Peng
YTYu Tang
Yu Tang
XCXiang-dong Chang
Xiang-dong Chang
Steel wire ropes are key load-bearing components in systems such as mine hoisting, bridge cableways, elevators, and cranes, and frictional wear is among the earliest occurring and most easily accumulated form of damage. Under actual working conditions, micro-relative sliding occurs both along the internal wires of the rope and at the contact surfaces with sheaves and ropes, leading to frictional wear, crack propagation, and fatigue failure. Frictional wear, a complex phenomenon influenced by structural layout, contact load, vibration conditions, lubrication, and environmental corrosion, critically determines the service life and load-bearing capacity of steel wire ropes. Recent experimental and numerical studies have significantly clarified the fundamental mechanisms and patterns of internal and external frictional wear in steel wire ropes, offering theoretical support for the distribution of wear, fatigue evolution, and fracture behavior. Meanwhile, non-destructive testing techniques have emerged as a vital tool for the real-time monitoring of wear conditions in steel wire ropes. This review summarizes the research progress on the generation, characteristics, effects, and protection of frictional wear in steel wire ropes, and proposes future directions for tribology and service safety research of steel wire ropes.

26 February 2026 in Sensors
Verified
Journal Article
Open access
PDF file
ZGZiheng Gu
Ziheng Gu
XHXiansong He
Xiansong He
YSYibo Song
Yibo Song
GLGongning Li
Gongning Li
SZShufeng Zhang
Shufeng Zhang
CLChuanjie Lu
Chuanjie Lu
Hydraulic systems are pivotal components in safety-critical aerospace and industrial applications, making reliable health monitoring essential. However, traditional data-driven diagnosis methods typically rely on static graph structures that fail to capture evolving sensor correlations during different fault modes. Furthermore, existing grid-based models often struggle to extract multi-resolution features and maintain performance under data-limited conditions. To address these challenges, this paper proposes a novel Dynamic Multi-Scale Graph Neural Network (DMS-GNN) for hydraulic system fault diagnosis. The framework integrates a hierarchical multi-scale feature extraction module to capture diverse fault signatures across different frequency bands. Crucially, a self-attention-based dynamic graph learner is introduced to adaptively infer latent sensor topologies end-to-end, eliminating the reliance on predefined physical connections. Experimental validation on a dedicated electro-hydraulic test bench demonstrates that the proposed DMS-GNN achieves a superior diagnostic accuracy of 98.47%, outperforming state-of-the-art baselines such as GraphSAGE, Static GCN, and GAT. The result confirms the efficacy of combining multi-scale temporal learning with dynamic spatial reasoning for robust multi-sensor fusion diagnosis.

1 May 2025
Verified
Conference Paper
Open access
PDF file
SPSpecial Equipment Safety Supervision Inspection Institute of Jiangsu Province
Special Equipment Safety Supervision Inspection Institute of Jiangsu Province
GLGongning Li
Gongning Li
LYLiang Ye
Liang Ye
GSGaofeng Song
Gaofeng Song
JLJiefeng Li
Jiefeng Li
ZLZhe Luo
Zhe Luo
Data augmentation is an effective method in machine learning to address data scarcity. When the cost of acquiring specific state data in professional fields are high, data augmentation can expand the limited datasets and improve model performance and generalization by creatively transforming existing data. In this study, by installing sensors on the lift door system, metrics such as door panels' 3-dimensional vibration accelerations, door motor current, distance of door panels, are continuously monitored in real time. Different deformation fault states of the lift door panels were simulated, and the original monitored metric data were collected under continuous operation. Data augmentation methods were used to transform part of the original data and create new data, thus expanding the dataset for machine learning. After preprocessing, the dataset formed a multi-dimensional feature dataset with fault labels, and a previously designed and validated high-accuracy AI model was used for training. The input layer of this model includes feature data of vibration acceleration and current, while the hidden layer consists of a combination of LSTM and fully connected layers. This study found that the use of data augmentation methods, such as random noise generation, random sub-sequence cropping, time warping, and Brownian motion simulation, had limited overall effect on the generalization ability of the AI model for classifying deformation faults of the lift door system. Among these methods, the model augmented using Brownian motion simulation achieved an accuracy of 67.2% in identifying "unknown" deformation levels of lift door faults. This indicates that the Brownian motion simulation data augmentation method provided the AI model with a limited level of generalization capability for identifying different types of lift door deformation faults.