Kun Huang

Dr. Kun Huang


Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 October 2025 in Lubricants
Verified
Journal Article
Open access
PDF file
KHKun Huang
Kun Huang
GLGongning Li
Gongning Li
XCXiang-dong Chang
Xiang-dong Chang
ZZZhou Zhou
Zhou Zhou
YPYuxing Peng
Yuxing Peng
RDRan Deng
Ran Deng
As a critical load-bearing component in mine hoisting systems, the service performance and lifespan of wire ropes are limited by the fretting wear behavior among their internal wires and strands. To investigate the effect of fretting parameters on the wear mechanisms in wire ropes, this paper systematically conducts fretting wear experiments on multi-wire contact pairs under varying fretting frequencies and tensile loads. The results show that as the fretting frequency increases from 0.5 Hz to 3.0 Hz, the coefficient of friction (COF) rises, with its steady-state value reaching approximately 0.65. Conversely, as the tension decreases from 150 N to 90 N, the COF increases, attaining a steady-state value of 0.71. The slip regime between the steel wires evolves from gross slip to partial slip with increasing frequency. With an increase in tensile load, the slip regime transitions from gross slip to partial slip and finally to adhesion. Higher fretting frequencies and greater tensile loads exacerbate both the wear rate and the severity of damage on the spiral contact wires inside the hoisting rope. The highest wear rate, 27.2 × 10−6 mm3/N·m, is observed at 3.0 Hz, while the maximum wear rate under tension is 39.6 × 10−6 mm3/N·m at 150 N. The dominant wear mechanisms at higher frequencies are abrasive wear, tribochemical reaction, and surface fatigue. Under greater tension, the primary wear mechanisms are abrasive wear, surface fatigue, and tribochemical reaction.

30 January 2026 in Lubricants
Verified
Journal Article
Open access
PDF file
LXLeyan Xia
Leyan Xia
GLGongning Li
Gongning Li
KHKun Huang
Kun Huang
YPYuxing Peng
Yuxing Peng
YTYu Tang
Yu Tang
XCXiang-dong Chang
Xiang-dong Chang
Steel wire ropes are key load-bearing components in systems such as mine hoisting, bridge cableways, elevators, and cranes, and frictional wear is among the earliest occurring and most easily accumulated form of damage. Under actual working conditions, micro-relative sliding occurs both along the internal wires of the rope and at the contact surfaces with sheaves and ropes, leading to frictional wear, crack propagation, and fatigue failure. Frictional wear, a complex phenomenon influenced by structural layout, contact load, vibration conditions, lubrication, and environmental corrosion, critically determines the service life and load-bearing capacity of steel wire ropes. Recent experimental and numerical studies have significantly clarified the fundamental mechanisms and patterns of internal and external frictional wear in steel wire ropes, offering theoretical support for the distribution of wear, fatigue evolution, and fracture behavior. Meanwhile, non-destructive testing techniques have emerged as a vital tool for the real-time monitoring of wear conditions in steel wire ropes. This review summarizes the research progress on the generation, characteristics, effects, and protection of frictional wear in steel wire ropes, and proposes future directions for tribology and service safety research of steel wire ropes.

15 October 2026 in Materials
Verified
Journal Article
Open access
PDF file
KHKun Huang
Kun Huang
XCXiang-dong Chang
Xiang-dong Chang
YPYuxing Peng
Yuxing Peng
Wei TangWei Tang
Wei Tang
ZZZhou Zhou
Zhou Zhou
RDRan Deng
Ran Deng
Mine hoisting ropes are subjected to time-varying tension, inertial loads, and constraints imposed by their helical structure during service. These factors readily induce normal compression and slight relative sliding between internal wires, thereby causing surface damage, residual strength degradation, and reduced reliability. In this paper, the internal wires of an 18 × 7 + IWS (Independent Wire Strand Core) mine hoisting rope are taken as the research object. A dynamic model of the hoisting rope and an analytical method for the contact load between internal wires are established. Tensile fracture tests are carried out to develop a residual strength degradation model for damaged wires, and a stress-strength interference reliability model is constructed to analyze the dynamic reliability evolution of damaged wires under different transverse loads. The results show that the rope tension fluctuates significantly with the operating stages during hoisting, and the internal wire forces exhibit marked positional differences. The core strand and interlayer contact regions are identified as potential damage-sensitive zones. As the transverse load increases from 80 N to 320 N, the breaking force of damaged wires decreases approximately linearly with increasing fretting cycles, and the strength degradation slope increases from −9.8 to −21.5, indicating that higher transverse contact loads significantly accelerate wire strength degradation. The working stress of the in-service wires approximately follows a normal distribution, with a mean value of 241.63 MPa and a standard deviation of 26.61 MPa. Under transverse loads of 80, 160, 240, and 320 N, the critical cycles at which the wire reliability begins to decrease rapidly are approximately 1.65 × 106, 1.57 × 106, 1.14 × 106, and 7.38 × 105, respectively.