Annette Muetze

Prof. Annette Muetze

orcid

Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 March 2017 in IEEE Transactions on Smart Grid
Verified
Journal Article
Closed access
Stefan LeitnerStefan Leitner
Stefan Leitner
MYMehrdad Yazdanian
Mehrdad Yazdanian
Ali Mehrizi-SaniAli Mehrizi-Sani
Ali Mehrizi-Sani
AMAnnette Muetze
Annette Muetze
Several microgrid control strategies are proposed and studied in the literature. However, there are still gaps in improving their transient behavior and studying their stability. This paper uses small-signal analysis to explore the behavior of internal model-based current and voltage controllers by deriving a state-space model and performing eigenvalue and sensitivity analysis on an islanded inverter-based microgrid system. The results are compared with those of the same microgrid but with PI-based current and voltage controllers. Simulation case studies are performed in the PSCAD/EMTDC environment to compare the transient behavior of both methods. Results show that internal model-based controllers have superior eigenvalue patterns that lead to increased stability and improved transient behavior.

20 April 2018 in IEEE Transactions on Power Systems
Verified
Journal Article
Closed access
SLStefan Leitner
Stefan Leitner
MYMehrdad Yazdanian
Mehrdad Yazdanian
SZSaleh Ziaeinejad
Saleh Ziaeinejad
Ali Mehrizi-SaniAli Mehrizi-Sani
Ali Mehrizi-Sani
AMAnnette Muetze
Annette Muetze
Three-phase passive harmonic filters (e.g., LCL filters) are often utilized to attenuate harmonic currents caused by pulse-width modulation (PWM) of voltage-sourced converters (VSC) to achieve high power quality. However, LCL filters may jeopardize the system stability due to their inherent susceptibility to resonance. This paper proposes an active damping current controller based on the internal model principle for a grid- connected VSC equipped with an LCL filter. This controller can be considered a high-order multi-input multi-output (MIMO) transfer function, implemented in the dq reference frame, includ- ing decoupling terms for improved transient behavior. Simulation case studies are performed in the PSCAD/EMTDC environment to evaluate the transient behavior of the controller and test its robustness against parameter variations and unbalanced and distorted grid conditions. Experimental results verify the performance of the proposed controller and confirm its ability to operate at low switching frequencies. The results are compared with two existing active damping strategies (virtual RC and notch filter methods), confirming that the proposed controller shows significantly improved robustness with no degradation of transient behavior, has the ability to operate at low switching frequencies, and does not need additional sensors

23 January 2017 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
JMJavier Martinez
Javier Martinez
Anouar BelahcenAnouar Belahcen
Anouar Belahcen
AMAnnette Muetze
Annette Muetze
This paper presents an analytical equation that relates the number of broken bars in the rotor of an induction machine to the vibrations of its stator. The relation is given in terms of both amplitudes and frequencies and is validated by numerical and experimental investigations. The amplitude of vibrations of some frequency components is shown to increase quadratically with the number of broken bars when the motor is operated at rated load. The frequency components of interest are in the range of two to four times the value of the supply frequency, which simplifies the implementation with relatively low cost instrumentation. The main focus and innovation of this paper is on the derivation of the analytical equations and their verification with numerical analysis and the comparison of both results to the experimental measurements.

28 May 2018 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
TTThomas Tanzer
Thomas Tanzer
HPHelmut Pregartner
Helmut Pregartner
MRMarkus Riedenbauer
Markus Riedenbauer
RLRobert Labinsky
Robert Labinsky
MWMichael Witlatschil
Michael Witlatschil
KKKlaus Krischan
Klaus Krischan
This paper analyzes the relationship between the experimentally determined magnetostriction of grain-oriented electrical steel (GOES) coils and the no-load noise of power transformers (PT). The main source of a PT's no-load noise is the magnetostrictive vibration of the magnetic core built with stacked GOES sheets. With an in-house measurement system, in which steel coils with a mass of up to 6,000 kg are measured, differences in the GOES materials' magnetostriction were identified. In this paper, we analyze the flux dependent behaviour and harmonic composition of the magnetostrictive properties of different steel coils. Based on the identified differences in the steel coils' magnetostriction, two experimental studies with PTs are provided showing exemplary results. The first study shows initial findings of the relationship between the magnetostriction of the deployed steel coils and the emitted no-load noise of model transformers. In a second study, the aforementioned investigations were extended with measurements of large power transformers (LPT). Both studies cover a correlation and performance analysis including comparisons of the noise related GOES certificate value B8 (also known as B800 value).

30 August 2018 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
MBMadeleine Bali
Madeleine Bali
AMAnnette Muetze
Annette Muetze
Literature agrees that cutting may damage the electromagnetic properties of electrical steel sheets, notably along the cut edge. However, statements on the depth of the deterioration vary. An analysis of the various results presented would allow for a better consideration of the material degradation in the modeling of the electromagnetic properties of the cut steel sheet in electric machines. To this aim, this paper analyzes and summarizes the deterioration depths presented in the literature. It not only provides an overview of the quantitative results, but discusses these in the context of the respective measurement method, since every technique used only provides an image of some of the aspects of the cut material affected by the cutting process.

18 June 2019 in IEEE Transactions on Industry Applications
Verified
Journal Article
Open access
Stefan LeitnerStefan Leitner
Stefan Leitner
HGHannes Gruebler
Hannes Gruebler
AMAnnette Muetze
Annette Muetze
Cogging torque reduction measures are hardly applied to low-cost sub-fractional hp BLDC motors, because the additional fabrication operations involved typically increase both the manufacturing complexity and cost significantly. By proposing an innovative punching layout, this paper shows how to minimize the high cogging torque of the mass-produced single-phase outer-rotor BLDC claw-pole motor–opposed to conventional cogging torque reduction–with no increase to the manufacturing cost. Systematically, a way is presented in which the selected introduction of auxiliary slots can double the cogging torque fundamental frequency, making stator claw skewing much more effective in reducing the cogging torque; both measures can be included at the stage of punching the steel sheets and subsequent deep-drawing thereof, at no additional cost. A detailed analysis of the effects of the cogging torque reduction measures on the most important motor performance parameters is conducted. The findings show that, with the exception of a small reduction of a few percent in the average output torque, the proposed design can reduce the peak-to-peak cogging torque by 70% in both the simulations and experiments. The reduction in the cogging torque translates into a reduction in the output torque ripple of 17 %, ensuring smoother operation especially at low speeds.