Indoor farming is among the approaches which can be adapted to improve agricultural sustainability and ensure the food security of countries. However, adopting indoor farming requires a high amount of energy to sustain the system. Incorporating a renewable energy system for supplying power to agricultural activities will allow the system to be more sustainable in the long run. An unconcentrated photovoltaic-thermoelectric generator (PV-TEG) hybrid system is designed based on the load requirement of an indoor farm. The hybrid system performance under Malaysia’s weather conditions was investigated and analyzed over three months. The designed system has shown its ability to provide sufficient power to the load, as well as supporting an additional load. Besides that, the TEGs power output was found to be dependent on the temperature as well as the types of connections used, where a higher temperature difference and series connection exhibited a better power output. Overall, the combination of the system showed that the addition of a TEG affects the efficiency and power output as compared to a standalone PV. Therefore, this implies that the hybrid system is able to exhibit a more positive outcome in certain weather conditions than a PV standalone system.
This chapter offers a comprehensive analysis of thermoelectric generators (TEGs), with a particular emphasis on their many designs, construction methods, and operational processes, all aimed at achieving optimal conversion of thermal energy into electrical energy. This chapter extensively examines the fundamental principles that control thermoelectric generators (TEGs), providing a complete examination of their respective merits and drawbacks in comparison with conventional energy conversion techniques. This study thoroughly investigates the key elements that have a significant impact on the performance of thermoelectric generators (TEGs), including the temperature gradient, heat source temperature, and load resistance. Moreover, the chapter explores the diverse range of thermoelectric materials employed in these generators and their significant qualities that directly affect the efficiency and power output of the devices. TEGs have been widely examined in terms of their practical applications, which include waste heat recovery, space exploration, and remote power generation. This chapter provides a comprehensive analysis of the obstacles and prospects associated with the incorporation of thermoelectric generators (TEGs) into renewable energy systems. Additionally, it evaluates the feasibility of scaling up TEG manufacturing to meet growing energy demands, with a specific focus on promoting sustainable energy solutions.
11 December 2019 in Journal of Electronic Materials
The application of laser powder bed fusion (LPBF) to 7xxx-series aluminum alloys is fundamentally limited by hot cracking and porosity. This study demonstrates that adding 5 wt.% AlCoCrFeNi2.1 high-entropy alloy (HEA) particles to 7075 aluminum alloy (AA7075) powder can effectively mitigate these issues. Microstructural characterization revealed that the HEA particles remained largely intact and formed a strong metallurgical bond with the α-Al matrix. Scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) analysis confirmed that this bonding is facilitated via the in situ formation of new intermetallic phases at the particle/matrix interface. X-ray diffraction (XRD) identified these phases as primarily Al5Co2 and Fe3Ni2. A key consequence of this reinforced interface is a significant change in cracking behavior; optical microscopy (OM) showed that long, continuous cracks typical of AA7075 were replaced by shorter, deflected cracks in the composite. While porosity was not eliminated, the addition of HEA stabilized the process, yielding a consistent density improvement of 0.5–1.5% across the processing window. This microstructural modification resulted in a substantial ~64% increase in average microhardness, which increased from 96.41 ± 9.81 HV0.5 to 158.46 ± 11.33 HV0.5. These results indicate that HEA reinforcement is a promising route for engineering the microstructure and improving the LPBF processability of high-strength aluminum alloys.
1 September 2021 in Journal of Physics: Conference Series
Solar Thermoelectric Generator (STEG), a hybridization system of thermoelectric generator (TEG) with a heat exchanger have been thoroughly explored because of its ability to produce both electricity and heat simultaneously. In this research, two tests were conducted: single TEG characterization test and STEG application. A theoretical modelling was developed based on the characterization test. For the STEG application, a solar parabolic dish concentrator and a single TEG were used to produce both heat and electricity simultaneously. An absorber plate placed on the focal point of the dish was used to facilitate the heat transfer of the reflected solar radiation to the TEG through the plate. The effects of various temperature difference were investigated. The absorber plate thickness was 1 mm and made up from copper to ensure high heat transfer rate and was well insulated so as to ensure minimal heat loss. To evaluate the performance of the TEG under the various temperatures, water-cooled cooling method (with water cooling jacket) and air-cooled cooling method (with finned heat sink and USB powered fan) were employed. Results showed that water-cooled cooling method was able to enhance the performance of STEG for higher power generation than air-cooled cooling method.
15 November 2024 in Journal of Mechanical Engineering
Thermoelectric generators (TEGs) offer the potential for converting waste heat into electricity, but their efficiency, particularly at low temperatures, remains inadequate. Plate-Fin Heat Exchangers (PFHEs) in TEG systems are not fully optimized, resulting in limited efficiency and applicability. The low conversion efficiency of TEGs means only a small fraction of waste heat is utilized, posing challenges to their long-term viability. While Genetic Algorithms (GAs) have shown promise in optimizing heat exchanger designs, advanced methods like Non-dominated Sorting Genetic Algorithm II (NSGAII) have yet to be fully applied for PFHE TEG design. This study addresses these challenges by using NSGA-II, combined with a semi-empirical model, to optimize PFHE design in TEG systems. The optimization focuses on refining fin design parameters such as number, width, and height while adhering toconstraints on fin area and pressure drop. The optimized design achieved a 3.94% increase in output power and a 1.72% increase in efficiency at 373.15 K, with conversion efficiency rising by 154.74% and maximum output power by 549.64% at 428.15 K. In conclusion, this research bridges the gap by applying NSGA-II to enhance PFHE design in TEGs, significantly improving performance and sustainability. Future work will explore alternative models and further optimization to achieve even higher efficiencies.