A new method of ultrasonic chemical mechanical polishing (CMP) combined with ultrasonic lapping is introduced to improve the machining performance of carbide silicon (SiC). To fulfill the method, an ultrasonic assisted machining apparatus is designed and manufactured. Comparative experiments with and without ultrasonic assisted vibration are conducted. According to the experimental results, the material removal rate (MRR) and surface generation are investigated. The results show that both ultrasonic lapping and ultrasonic CMP can decrease the two-body abrasion and reduce the peak-to-valley (PV) value of surface roughness, the effect of ultrasonic in lapping can contribute to the higher MRR and better surface quality for the following CMP. The ultrasonic assisted vibration in CMP can promote the chemical reaction, increase the MRR and improve the surface quality. The combined ultrasonic CMP with ultrasonic lapping achieved the highest MRR of 1.057 μm/h and lowest PV value of 0.474 μm. Therefore this sequent ultrasonic assisted processing method can be used to improve the material removal rate and surface roughness for the single crystal SiC wafer.
The material of disc cutters is important to full-face tunnel boring machines (TBM). In recent years, disc cutters were optimized and tested by many scholars all around the world. H13(4Cr5MoSiV1) steel is widely used due to its excellent properties, especially in TBM disc cutters. In this paper, H13 steel with optimized composition was prepared and heat treatment. The high temperature compression of H13 steel was conducted at the temperatures ranging from 100 °C to 700 °C, with strain rate at 0.01 s−1. The stress-strain curves, Rockwell hardness and microstructure of H13 steel after compression were obtained and analyzed. The results showed that the compression strength and hardness decreased as the temperature increased; and the compression strength, hardness and ductility decreased rapidly between 600 °C and 700 °C, HR700 (the hardness of H13 steel at 700 °C) only reached 33.23 HRC. It is not recommended for TBM disc cutters to work in an environment over 600 °C.
SiCp/6061Al composites have been developed and widely applied in many fields, such as automobile, aerospace, shipping, and so on. Considering heat treatment, service environment, and strength of composites, this paper comprehensively studies the mechanical properties of SiCp/6061Al composites with a large range of SiC mass fractions under T6 treatments and different tensile temperatures. SiCp/6061Al composites were successfully prepared by hot press sintering at various SiC mass fractions (0–30%), and the influences of SiC concentration and T6 treatment on the mechanical properties of composites were characterized via tensile tests at room temperature, 100, and 200 °C. Microstructure and fracture surfaces of composites with various SiC concentrations were further analyzed by optical microscope and SEM. The formula for the biggest critical reinforcement concentration for the saturated distribution of SiC is proposed to reveal the strengthening rule of different SiC concentrations. Results show that the effect of T6 treatment on the mechanical properties of composites is a marked increase in tensile strength and an obvious decrease in elongation. The increase in the SiC mass fraction, except at 30%, is able to bring an increase in tensile strength and a decrease in elongation, and the change of the elongation is insignification in T6-treated specimens. The tensile strength of T6-treated specimens decreases as temperature increases, and the composite has a maximum elongation at 100 °C.
Disc cutters are the main working tools of full-face hard rock tunnel boring machine (TBM). They are in direct contact with rocks, sustaining enormous loads and vibrations in practical constructions. Therefore, The wear of the disc cutters is very severe and would cause huge economic costs. In this study, the abrasive wear performance of disc cutters’ material (H13 steel) was analyzed by pin-on-disc wear tests in contact with three types of rocks (sandstone, granite and gneiss) under different loads (100 N and 200 N). The friction coefficient was recorded during the tests. The wear rate of H13 steel and maximum wear depth of rocks were calculated and measured. The worn surfaces of H13 steel were observed. Results showed that the friction coefficient, the wear rate of H13 steel and the maximum wear depth of rocks under the load of 100 N was lower than those of 200 N. The main wear mechanism of H13 steel in contact with sandstone was three-body wear, while the main wear mechanism of H13 steel in contact with high-strength rocks (granite and gneiss) was abrasive wear. The study of wear performance and mechanisms of H13 steels sliding against different rock types would provide theoretical supports for the construction of TBM under various geological conditions.
18 February 2022 in Journal of Materials Engineering and Performance
Due to its high specific strength and low coefficient of thermal expansion, Al/SiCp homogenous composites (HC) have become a widely used material in automobile and other fields. The application of components with different internal and external material performance requirements such as automobile pistons and brake disks has promoted the development of functionally graded materials (FGM). Therefore, Al/SiCp composites are expected to be applied on a large scale. Al6061/SiCP composites were prepared by vacuum hot-pressed sintering whose microstructure observation is carried out and mechanical properties are tested. The hardness of the Al/SiC HC increases gradually as the SiC content increases from 0 to 30 wt.%. The hardness values of the T6-treated Al6061/SiCp HC with SiC mass fractions of 0, 5, 10, 15, 20, 25, and 30% are 97, 101, 104, 111, 113, 118, and 125HV, respectively, and it is a maximum increase of 117.48% compared with HC without T6 treatment. The flexural strength increases and the deflection decreases with the increase of SiC content, and T6 heat treatment also improves the flexural strength of all composites with about 30% increase over that without T6 heat treatment. When the load was applied from the layer with high SiC content of FGM whose interlayer difference is 5%, the strength and deflection were superior to those of the HC.