The material of disc cutters is important to full-face tunnel boring machines (TBM). In recent years, disc cutters were optimized and tested by many scholars all around the world. H13(4Cr5MoSiV1) steel is widely used due to its excellent properties, especially in TBM disc cutters. In this paper, H13 steel with optimized composition was prepared and heat treatment. The high temperature compression of H13 steel was conducted at the temperatures ranging from 100 °C to 700 °C, with strain rate at 0.01 s−1. The stress-strain curves, Rockwell hardness and microstructure of H13 steel after compression were obtained and analyzed. The results showed that the compression strength and hardness decreased as the temperature increased; and the compression strength, hardness and ductility decreased rapidly between 600 °C and 700 °C, HR700 (the hardness of H13 steel at 700 °C) only reached 33.23 HRC. It is not recommended for TBM disc cutters to work in an environment over 600 °C.
SiCp/6061Al composites have been developed and widely applied in many fields, such as automobile, aerospace, shipping, and so on. Considering heat treatment, service environment, and strength of composites, this paper comprehensively studies the mechanical properties of SiCp/6061Al composites with a large range of SiC mass fractions under T6 treatments and different tensile temperatures. SiCp/6061Al composites were successfully prepared by hot press sintering at various SiC mass fractions (0–30%), and the influences of SiC concentration and T6 treatment on the mechanical properties of composites were characterized via tensile tests at room temperature, 100, and 200 °C. Microstructure and fracture surfaces of composites with various SiC concentrations were further analyzed by optical microscope and SEM. The formula for the biggest critical reinforcement concentration for the saturated distribution of SiC is proposed to reveal the strengthening rule of different SiC concentrations. Results show that the effect of T6 treatment on the mechanical properties of composites is a marked increase in tensile strength and an obvious decrease in elongation. The increase in the SiC mass fraction, except at 30%, is able to bring an increase in tensile strength and a decrease in elongation, and the change of the elongation is insignification in T6-treated specimens. The tensile strength of T6-treated specimens decreases as temperature increases, and the composite has a maximum elongation at 100 °C.
1 January 2022 in Materials Science and Engineering: A
Down-the-hole (DTH) hammer drilling with reverse circulation is a novel, mobile, high-speed drilling system suitable for the specific requirements of mine rescue. This technology can be applied to shorten the rescue time during mine accidents. The performance of reverse circulation (RC) drilling depends on the structural design of the drill bit. An orthogonal experimental design is executed to investigate the effect of the structural design parameters of the large-diameter drill bit for drilling rescue wells on the cutting carrying capacity and reverse circulation performance. This study employs computational fluid dynamics (CFD) software to solve the Navier–Stokes equation for three-dimensional steady flow and calculate the flow field around the drill bit to evaluate the RC efficiency. Six key geometric parameters were proven to have a direct influence on the RC performance, including the diameter of suction nozzles Dn, the length of nozzles L, the quantity of nozzles N, the diameter of the pilot hole Dg, the inclination angle of nozzles θs, and the deflection angle of nozzles θd. The CFD simulation experiments were implemented according to the orthogonal array L18(37) and were analyzed using the range, variance, and regression analysis. A mathematical model was developed for the RC efficiency to understand the effect of the factors. The results show that the diameter of suction nozzles Dn has an essential effect on the RC performance of the drill bit. An ideal combination is Dn = 20 mm, L = 50 mm, N = 3, Dg = 50 mm, and θs = 35°, θd = 10°, which was obtained through variance analysis and validated via CFD simulation for higher efficiency. To verify its real performance, a large-diameter RC drill bit with a diameter of 1.2 m was manufactured and tested in the field. The result demonstrated that the drill bit had excellent cutting transport and reverse circulation performance.