Andrzej Fijołek

Dr. Andrzej Fijołek

Faculty of Foundry Engineering, AGH University of Krakow, Kraków, Małopolskie, Poland
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 August 2020 in Materials
Verified
Journal Article
Open access
PDF file
AFAndrzej Fijołek
Andrzej Fijołek
JLJanusz Lelito
Janusz Lelito
HKHalina Krawiec
Halina Krawiec
JRJagoda Ryba
Jagoda Ryba
LRLukasz Rogal
Lukasz Rogal
The aim of this work was to monitor the corrosion rate of the Mg72Zn24Ca4 and Zn87Mg9Ca4 alloys. The purity of the alloying elements was 99.9%. The melt process was carried out in an induction furnace. The melting process took place under the cover of an inert gas (argon). The copper form was flooded by liquid alloy. Then, in order to obtain ribbons, the cast alloy, in rod shape, was re-melted on the melt spinning machine. The corrosion resistance of both alloys has been determined on the basis of the following experiments: measurements of the evolution of OCP (open circuit potential), LSV (linear sweep voltamperometry) and EIS (electrochemical impedance spectroscopy). All corrosion tests were carried out in Ringer’s solution at 37 °C and pH 7.2. The corrosion tests have revealed that the zinc alloy, Zn87Mg9Ca4, exhibits significantly higher corrosion resistance in the Ringer solution compared to the magnesium alloy, Mg72Zn24Ca4. Moreover, it has been shown that the cathodic reaction proceeds faster on the surface of ribbons. EIS measurements show that the dissolution of Mg alloy proceeds with two steps: transfer of Mg2+ ions to the Ringer solution and then the formation of the corrosion products, which are deposited on the surface of magnesium alloy. It has been revealed, too, that for both bulk materials, diffusion of chloride ions through the corrosion product’s layer takes place.

26 August 2022 in Archives of Metallurgy and Materials
Verified
Journal Article
Closed access
PDF file
Aldona Garbacz-KlempkaAldona Garbacz-Klempka
Aldona Garbacz-Klempka
MPMarcin Piękoś
Marcin Piękoś
MPMałgorzata Perek-Nowak
Małgorzata Perek-Nowak
JKJanusz Kozana
Janusz Kozana
PŻPaweł Leszek Żak
Paweł Leszek Żak
MSM. Stróżyk
M. Stróżyk
One of the most interesting categories of artifacts for archaeometallurgical research includes deposits of bronze items, so-called “metallurgists hoards”. They contain, aside of final products, many fragments of raw material and, moreover, metallurgical tools. An important source for the studies on the history of metallurgical technology is hoard from Przybysław, Greater Poland district. Thus, the aim of the work is the identification and interpretation of bronze-working practices and strategies adopted by prehistoric communities of the Late Bronze Age and the Early Iron Age (ca. 600 BC). The examined objects are characterized in terms of their design, structure, and chemical composition. The methods chosen for the studies of artifacts include: metallographic macro- and microscopic observations using optical microscopy (OM) and scanning electron microscopy (SEM), the analysis of chemical composition with the methods of energy dispersive X-ray spectroscopy (EDS), and X-ray fluorescence (ED-XRF). The thermodynamic analysis of the alloys was performed on the basis of the CALPHAD method. The experimental melts allowed to verify the theoretical considerations and to determine the characteristic temperatures of changes. The old casting technology can be analyzed basing on computer modeling and computer simulation methods. Simulations in the MAGMASOFT® software are a good example to illustrate how to fill a mould cavity with a molten bronze for a hoop ornament. It is also an appropriate tool to determine temperature distribution in a mould. The simulations also show the possible disadvantages with this old technology.

31 October 2025 in Polymers
Verified
Journal Article
Open access
PDF file
Katarzyna Aleksandra Major-GabryśKatarzyna Aleksandra Major-Gabryś
Katarzyna Aleksandra Major-Gabryś
Dawid HalejcioDawid Halejcio
Dawid Halejcio
AFAndrzej Fijołek
Andrzej Fijołek
JMJan Marosz
Jan Marosz
Marcin GórnyMarcin Górny
Marcin Górny
Resin-based binders are one of the main materials used in foundry molding and core sands. Self-curing sand with furfuryl resin is one of the most popular technologies in the production of molds and cores for complex, critical castings made of iron and non-ferrous alloys. It has dominated small-batch production and the production of large-sized castings. This work is part of the research on new molding sands for mold additive manufacturing (3D printing). Three-dimensional printing technology in the production of sand-casting molds and cores is finding increasing industrial application in the production of castings from non-ferrous metal alloys. The aim of the research presented in this paper was to determine the influence of furfuryl resin type (classical and designed for 3D printing of sand molds) on cast iron casting properties. The pouring parameters were elaborated on the basis of the MAGMA software. Microscopic observations of castings, produced in classical and 3D-printed molds, were conducted, as well as an assessment of the roughness of the samples. The gas emissions from molding sands with both types of furfuryl resin were tested and analyzed in the context of the roughness of the castings obtained. It was proven that molding sand with furfuryl resin designed for 3D printing was characterized by lower gas emissions, which, in the case of molding sands with organic binders, is beneficial from an environmental point of view.

8 February 2024 in Archives of Foundry Engineering
Verified
Journal Article
Closed access
AFAndrzej Fijołek
Andrzej Fijołek
The work presents monitoring of the corrosion rate for pure magnesium and the binary magnesium alloy Mg72Zn28. Alloying elements with a purity of 99.9% were used. The melting was performed under the protection of inert gas - argon in an induction furnace. The liquid alloy was poured into a copper mold. In order to make amorphous ribbons, the obtained samples in the form of rods were re-melted on a melt spinner machine. The next step was to perform corrosion tests in Ringer's solution. Corrosion tests were carried out at a temperature of 37°C and pH 7.2. The purpose of using Ringer's solution was to recreate the conditions for the body fluids of the human body. The use of the following research methods, such as: OCP (open circuit potential), LSV (linear sweep voltammetry) and EIS (electrochemical impedance spectroscopy), was aimed at determining the corrosion resistance of the tested materials. Tests carried out in Ringer's solution showed that pure magnesium has significantly worse corrosion resistance than the binary Mg72Zn28 alloy. The conducted research also confirmed that the cathodic reaction takes place faster on the surface of amorphous ribbons. It was also confirmed that for both crystalline materials there is diffusion of chloride ions through the corrosion product layer. SEM-EDS tests were performed on the surface of an amorphous ribbon of the Mg72Zn28 alloy after corrosion in Ringer's solution.

23 December 2025 in Journal of Casting & Materials Engineering
Verified
Journal Article
Open access
PDF file
KMKarolina Marlicka
Karolina Marlicka
AFAndrzej Fijołek
Andrzej Fijołek
Aldona Garbacz-KlempkaAldona Garbacz-Klempka
Aldona Garbacz-Klempka
MPMarcin Piękoś
Marcin Piękoś
This article presents an interdisciplinary approach to the reconstruction of a copper-alloy artefact using reverse engineering techniques combined with modern digital and manufacturing technologies. The research was motivated by the need to better understand historical casting techniques while preserving the integrity of cultural heritage objects through non-destructive methods. The study integrates 3D scanning, CAD-based modelling, numerical simulations, investment casting, and metal additive manufacturing. The geometry of the artefact was captured using high-resolution 3D scanning, enabling the development of two CAD models: one representing the preserved state of the object and a second reconstructed model with the missing fragment digitally restored. Both models were used for numerical simulations of mould filling, solidification, cooling, and porosity formation performed in MAGMASOFT® 6.1, allowing the assessment of technological feasibility and defect formation. Based on the simulation results, physical replicas were produced using investment casting and selective laser melting.The obtained numerical and experimental results were compared in terms of geometry reproduction, surface characteristics, and predicted versus observed casting behaviour. The study demonstrates that the combination of digital reconstruction, simulation tools, and experimental manufacturing provides a reliable framework for analysing historical metallurgical processes. The proposed methodology supports both scientific interpretation and the practical reconstruction of heritage objects and can be applied to a wide range of archaeometallurgical studies.

23 December 2025 in Journal of Casting & Materials Engineering
Verified
Journal Article
Open access
PDF file
KMKarolina Marlicka
Karolina Marlicka
AFAndrzej Fijołek
Andrzej Fijołek
Aldona Garbacz-KlempkaAldona Garbacz-Klempka
Aldona Garbacz-Klempka
MPMarcin Piękoś
Marcin Piękoś
This article presents an interdisciplinary approach to the reconstruction of a copper-alloy artefact using reverse engineering techniques combined with modern digital and manufacturing technologies. The research was motivated by the need to better understand historical casting techniques while preserving the integrity of cultural heritage objects through non-destructive methods. The study integrates 3D scanning, CAD-based modelling, numerical simulations, investment casting, and metal additive manufacturing. The geometry of the artefact was captured using high-resolution 3D scanning, enabling the development of two CAD models: one representing the preserved state of the object and a second reconstructed model with the missing fragment digitally restored. Both models were used for numerical simulations of mould filling, solidification, cooling, and porosity formation performed in MAGMASOFT® 6.1, allowing the assessment of technological feasibility and defect formation. Based on the simulation results, physical replicas were produced using investment casting and selective laser melting.The obtained numerical and experimental results were compared in terms of geometry reproduction, surface characteristics, and predicted versus observed casting behaviour. The study demonstrates that the combination of digital reconstruction, simulation tools, and experimental manufacturing provides a reliable framework for analysing historical metallurgical processes. The proposed methodology supports both scientific interpretation and the practical reconstruction of heritage objects and can be applied to a wide range of archaeometallurgical studies.