Katarzyna Aleksandra Major-Gabryś

Dr. Katarzyna Aleksandra Major-Gabryś

AGH-University of Science and Technology, Faculty of Foundry Engineering, Kraków, Poland
orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 February 2019 in Journal of Materials Engineering and Performance
Verified
Journal Article
Open access
PDF file
Katarzyna Aleksandra Major-GabryśKatarzyna Aleksandra Major-Gabryś
Katarzyna Aleksandra Major-Gabryś
The paper describes the current state of knowledge in a field where change has been driven in foundry molding sand practice due to the increasing requirements regarding environmental protection. These trends must take into account not only the technological quality and economics of their production process, but also the increasingly stringent requirements related to environmental protection. As part of this study, tests were performed in relation to reducing the toxicity of current molding sands with organic binders, so as to develop new organic binders for foundry practice. Molding sands with binders having various contents of furfuryl alcohol were tested. It was shown that reducing the total furfuryl alcohol content in the binder results in lower strength properties of the molding sands in practice. It was also suggested to replace the use of a furfuryl binder with one based on alkyd resin. The final stage of the study was to demonstrate the desirability of using biomaterials as a component of organic binders for foundry molding sands. Compositions: typical synthetic resins and biodegradable materials were designed as binders to improve the quality of the organic binders used with molding sands.

1 June 2015 in Archives of Foundry Engineering
Verified
Journal Article
Open access
SDSt. M. Dobosz
St. M. Dobosz
AGA. Grabarczyk
A. Grabarczyk
Katarzyna Aleksandra Major-GabryśKatarzyna Aleksandra Major-Gabryś
Katarzyna Aleksandra Major-Gabryś
JJJaroslaw Jakubski
Jaroslaw Jakubski
Modern techniques of castings production, including moulding sands production, require a strict technological regime and high quality materials. In the case of self-hardening moulding sands with synthetic binders those requirements apply mainly to sand, which adds to more than 98% of the whole moulding sand mixture. The factors that affect the quality of the moulding sands are both chemical (SiO2, Fe2O3 and carbonates content) and physical. Among these factors somewhat less attention is paid to the granulometric composition of the sands. As a part of this study, the effect of sand quality on bending strength Rgu and thermal deformation of self-hardening moulding sands with furfural and alkyd resin was assessed. Moulding sands with furfural resin are known [1] to be the most susceptible to the sand quality. A negative effect on its properties has, among others, high content of clay binder and so-called subgrains (fraction smaller than 0,1mm), which can lead to neutralization of acidic hardeners (in the case of moulding sands with furfuryl resin) and also increase the specific surface, what forces greater amount of binding agents. The research used 5 different quartz sands originating from different sources and characterized with different grain composition and different clay binder content.

2 March 2024 in International Journal of Metalcasting
Verified
Journal Article
Open access
PDF file
NANurul Anwar
Nurul Anwar
Katarzyna Aleksandra Major-GabryśKatarzyna Aleksandra Major-Gabryś
Katarzyna Aleksandra Major-Gabryś
KJKalle Jalava
Kalle Jalava
JOJuhani Orkas
Juhani Orkas
Renewed interest in inorganic binders for sand molding has also intensified research on different forms of it. In this study, solid inorganic sodium silicate binder was tested with different additives to see how these affected the silica mold quality. The five additives used were: glucose, sucrose, boric acid, aluminum oxide and iron(III)oxide powders. The mold quality was assessed through tests like bending strength, tensile strength, hot distortion, wear resistance, gas evolution and collapsibility tests. In addition, SEM imaging was done on some select mold fracture samples. In the end, a casting trial was carried out followed by a surface roughness and defects analysis. A reduction in mold strength was noticed with glucose and boric acid, while collapsibility was improved by glucose, sucrose and boric acid additives. Casting trials have shown the best surface finish to be obtained with sucrose additive. All the casts in general showed some penetration; however, repeat casts have proven that altering some casting parameters could result in casts with excellent surface finish using solid silicates.

1 March 2017 in Archives of Metallurgy and Materials
Verified
Journal Article
Open access
PDF file
DBDana Bolibruchová
Dana Bolibruchová
LRL. Richtárech
L. Richtárech
SDS. M. Dobosz
S. M. Dobosz
Katarzyna Aleksandra Major-GabryśKatarzyna Aleksandra Major-Gabryś
Katarzyna Aleksandra Major-Gabryś
This article describes the impact of the metal mould temperature change in eliminating the adverse effect of iron in the AlSi7Mg0.3 alloy. The kind of phases based on iron to be formed in aluminium alloys is determined by the alloy chemical composition, the melt overheating temperature prior to casting, and the cooling rate during crystallisation. In the experiment, we used three various mould temperatures, and their impact on the possible change in the adverse Al5FeSi phase, excreted in a needle form to a more compact form of Chinese writing or skeleton units. The experimental part did not use melt overheat that would result in impairment of the melt, for example due to increased gassing of the melt, as well as in a greater load on the smelting unit, thus resulting in increased energy expenditure. We can conclude from the obtained results that the mould temperature change does not have an adequate effect in eliminating the adverse effect of iron in Al-Si-Mg alloys.

6 October 2015 in Archives of Foundry Engineering
Verified
Journal Article
Open access
PDF file
SDSt. M. Dobosz
St. M. Dobosz
Katarzyna Aleksandra Major-GabryśKatarzyna Aleksandra Major-Gabryś
Katarzyna Aleksandra Major-Gabryś
AGA. Grabarczyk
A. Grabarczyk
The article shows the influence of environment requirements on changes in different foundry moulding sands technologies such as cold box, self-hardening moulding sands and green sands. The aim of the article is to show the possibility of using the biodegradable materials as binders (or parts of binders’ compositions) for foundry moulding and core sands. The authors concentrated on the possibility of preparing new binders consisting of typical synthetic resins - commonly used in foundry practice - and biodegradable materials. According to own research it is presumed that using biodegradable materials as a part of new binders’ compositions may cause not only lower toxicity and better ability to reclaim, but may also accelerate the biodegradation rate of used binders. What’s more, using some kinds of biodegradable materials may improve flexibility of moulding sands with polymeric binder. The conducted research was introductory and took into account bending strength and thermal properties of furan moulding sands with biodegradable material (PCL). The research proved that new biodegradable additive did not decrease the tested properties.

1 September 2013 in Archives of Metallurgy and Materials
Verified
Journal Article
Open access
PDF file
JJJ. Jakubski
J. Jakubski
PMPaweł Malinowski
Paweł Malinowski
SDSt.M. Dobosz
St.M. Dobosz
Katarzyna Aleksandra Major-GabryśKatarzyna Aleksandra Major-Gabryś
Katarzyna Aleksandra Major-Gabryś
Application of modern technological solutions, as well as the economic and ecological solutions, is for foundries one of the main aspects of the competitiveness on the market for castings. IT solutions can significantly support technological processes. This article presents neural networks with different structures that have been used to determine the moisture content of the moulding sand based on the moulding sand selected properties research results. Neural networks were built using Matlab software. Moulding sand properties chosen for quality control processes were selected based on wide previous results. For the proposed moulding sand properties, neural networks can be a useful tool for predicting moisture content. The structure of artificial neural network do not have a significant influence on the obtained results. In subsequent studies on the use of neural networks as an application to support the green moulding sand rebonding process, it must be determined how factors such as environmental humidity and moulding sand temperature will affect the accuracy of data obtained with the use of artificial neural networks.